Comparison of manual and image processing methods of End-Milling burr measurement

被引：0
|
作者：
School of Engineering and Physics, University of the South Pacific, Suva, Fiji [1 ]
不详 [2 ]
机构：
[1] School of Engineering and Physics, University of the South Pacific, Suva
[2] Knowledge Management and Mining, Toronto
来源：
Lect. Notes Electr. Eng. | / 133-137期
关键词：
Burr height; End-milling; Image processing;
D O I：
10.1007/978-3-319-06773-5_19
中图分类号：
学科分类号：
摘要：
This paper compares the results for manual method of burr height measurement with the image-processing technique for end-milled work-pieces under various conditions. The manual method refers to the traditional way where a few readings are taken at random locations using a microscope and the burr height is approximated with an average value. In contrast, the image processing technique analyzes the whole burr profile as seen through the lens of the microscope and captured using a digital camera. With the results obtained using the image processing method as reference, the results show a significant difference between the two average readings in most cases and generally the percentage error is greater for work-pieces with irregular burrs. © Springer International Publishing Switzerland 2015.
引用
收藏
页码：133 / 137
页数：4
相关论文
共 37 条
  • [21] Practical Aspects of Weight Measurement Using Image Processing Methods in Waterfowl Production
    Szabo, Sandor
    Alexy, Marta
    AGRICULTURE-BASEL, 2022, 12 (11):
  • [22] Automatic measurement and recognition of yarn snarls by digital image and signal processing methods
    Xu, Bin Gang
    Murrells, Charlotte Marion
    Tao, Xiao Ming
    TEXTILE RESEARCH JOURNAL, 2008, 78 (05) : 439 - 456
  • [23] Comparison of Image Processing and Classification Methods for a Better Diet Decision-Making
    Abbasi, Maryam
    Cardoso, Filipe
    Martins, Pedro
    BIOINFORMATICS AND BIOMEDICAL ENGINEERING, IWBBIO 2023, PT I, 2023, 13919 : 390 - 403
  • [24] The Comparison of the Edge Detection Methods in the Determination of Yarn Hairiness through Image Processing
    Telli, Abdurrahman
    TEKSTIL VE KONFEKSIYON, 2021, 31 (02): : 91 - 98
  • [25] Image Processing of Advance Milling Cutters to Automate the Measurement of the Geometric Parameters of the Cutting Edge on Optical Measuring Systems
    Pivkin, Petr M.
    Minin, Ilya, V
    Volosova, Marina A.
    Romanov, Vitaly B.
    Nadykto, Alexsey B.
    SPIE FUTURE SENSING TECHNOLOGIES 2021, 2021, 11914
  • [26] An Indicative End-milling Condition Decision Support System Using Data-Mining for Difficult-to-cut Materials Based on Comparison with Irregular Pitch and Lead End-mill and General Purpose End-mill
    Kodama, Hiroyuki
    Hirogaki, Toshiki
    Aoyama, Eiichi
    Ogawa, Keiji
    ADVANCES IN ABRASIVE TECHNOLOGY XVI, 2013, 797 : 177 - +
  • [27] Shack-Hartmann wavefront sensor image analysis: a comparison of centroiding methods and image-processing techniques
    Nightingale, Alice M.
    Gordeyev, Stanislav
    OPTICAL ENGINEERING, 2013, 52 (07)
  • [28] In-plane optical measurement of vibrations of MEMS: gradient methods using interferometry and image processing
    Cretin, B
    Serio, B
    Vairac, P
    MICROSYSTEMS ENGINEERING: METROLOGY AND INSPECTION III, 2003, 5145 : 161 - 168
  • [29] Image Processing of Mg-Al-Sn Alloy Microstructures for Determining Phase Ratios and Grain Size and Correction with Manual Measurement
    Ercetin, Ali
    Akkoyun, Fatih
    Simsir, Ercan
    Pimenov, Danil Yurievich
    Giasin, Khaled
    Chandrashekarappa, Manjunath Patel Gowdru
    Lakshmikanthan, Avinash
    Wojciechowski, Szymon
    MATERIALS, 2021, 14 (17)
  • [30] Comparison of deep learning and analytic image processing methods for autonomous inspection of railway bolts and clips
    Aldao, E.
    Fernandez-Pardo, L.
    Gonzalez-deSantos, L. M.
    Gonzalez-Jorge, H.
    CONSTRUCTION AND BUILDING MATERIALS, 2023, 384
1234