Microstructure and mechanical properties of GH3535 superalloy joints using keyhole TIG welding

被引：2
作者：
Fang, Huisheng [1 ,2 ]
Li, Zhijun [2 ]
Yuan, Xiaodan [2 ]
Liu, Fang [1 ]
Zhu, Qingchun [2 ]
Yan, Dezhong [2 ]
Liang, Jianping [2 ]
机构：
[1] Univ Shanghai Sci & Technol, Sch Mat Sci & Engn, Shanghai, Peoples R China
[2] Chinese Acad Sci, Shanghai Inst Appl Phys, Shanghai, Peoples R China
来源：
NUCLEAR ENGINEERING AND DESIGN | 2025年 / 432卷
基金：
中国国家自然科学基金;
关键词：
Keyhole TIG welding GH3535 superalloy; single-pass welding microstructure mechanical; property; HEAT-AFFECTED ZONE; THERMAL CYCLE; WELDED-JOINT; PRECIPITATION; TRANSITION; EVOLUTION;
D O I：
10.1016/j.nucengdes.2024.113780
中图分类号：
TL [原子能技术]; O571 [原子核物理学];
学科分类号：
0827 ; 082701 ;
摘要：
Single-pass keyhole TIG welding (K-TIG) was used to weld 10-mm-thick GH3535 superalloy plates without filler metal and groove preparation. The microstructure and mechanical properties of GH3535 superalloy welded joints were investigated. The results show that columnar crystals symmetrically grow in the fusion zone (FZ) and the contact angle between the symmetric columnar crystals is approximately 115 degrees. A few eutectic phases of M6C- gamma are observed in a partially melted zone (PMZ) of the heat-affected zone (HAZ). The microhardness of HAZ is higher than that of FZ and the base metal (BM). The tensile strength of joints at room temperature, 650 degrees C, and 700 degrees C were 98%, 101%, and 99% of the BM, respectively. The results show that K-TIG welding is suitable for joining middle-thick GH3535 superalloy plates.
引用
收藏
页数：11
相关论文
共 45 条
  • [1] Microstructure and hardness studies of the electron beam welded zone of Hastelloy C-276
    Ahmad, M
    Akhter, JI
    Akhtar, M
    Iqbal, M
    Ahmed, E
    Choudhry, MA
    [J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2005, 390 (1-2) : 88 - 93
  • [2] Microstructural Analysis of K-TIG-Welded New Ni-Based Superalloy VDM Alloy 780
    Ariaseta, Achmad
    Khan, Abdul Khaliq
    Andersson, Joel
    Ojo, Olanrewaju
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2024, 55 (08): : 2952 - 2976
  • [3] Study of Variation in Fracture Location of Electron Beam-Welded Hastelloy C-276 Sheets under Uniaxial Tension
    Bal, Kalinga Simant
    Dutta Majumdar, Jyotsna
    Roy Choudhury, Asimava
    [J]. JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2020, 29 (12) : 8370 - 8394
  • [4] Characterization of complex carbide-silicide precipitates in a Ni-Cr-Mo-Fe-Si alloy modified by welding
    Bhattacharyya, D.
    Davis, J.
    Drew, M.
    Harrison, R. P.
    Edwards, L.
    [J]. MATERIALS CHARACTERIZATION, 2015, 105 : 118 - 128
  • [5] Microstructure characterisation of multi-principal element alloys welds produced by electron beam welding
    Buzolin, Ricardo Henrique
    Richter, Tim
    Pixner, Florian
    Rhode, Michael
    Schroepfer, Dirk
    Enzinger, Norbert
    [J]. MATERIALS & DESIGN, 2023, 225
  • [6] Experimental study and numerical optimization on a vane-type separator for bubble separation in TMSR
    Cai, Baowei
    Wang, Jianjun
    Sun, Licheng
    Zhang, Nana
    Yan, Changqi
    [J]. PROGRESS IN NUCLEAR ENERGY, 2014, 74 : 1 - 13
  • [7] Microstructure and local strains in GH3535 alloy heat affected zone and their influence on the mechanical properties
    Chen, Shuangjian
    Tsang, D. K. L.
    Jiang, Li
    Yu, Kun
    Li, Chaowen
    Li, Zhong
    Li, Zhijun
    Zhou, Xingtai
    Yang, Jianguo
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 699 : 48 - 54
  • [8] Microstructure and mechanical properties of UNS N10003 alloy welded joints
    Chen, Shuangjian
    Ye, Xiang-Xi
    Yu, Kun
    Li, Chaowen
    Li, Zhijun
    Li, Zhong
    Zhou, Xingtai
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 682 : 168 - 177
  • [9] Molten salt corrosion (FLiNaK) of a Ni-Mo-Cr alloy and its welds for application in energy-generation and energy-storage systems
    Danon, A. E.
    Muransky, O.
    Karatchevtseva, I.
    Zhang, Z.
    Li, Z. J.
    Scales, N.
    Kruzic, J. J.
    Edwards, L.
    [J]. CORROSION SCIENCE, 2020, 164
  • [10] Investigation into the viability of K-TIG for joining armour grade quenched and tempered steel
    Fei, Zhenyu
    Pan, Zengxi
    Cuiuri, Dominic
    Li, Huijun
    Wu, Bintao
    Ding, Donghong
    Su, Lihong
    Gazder, Azdiar A.
    [J]. JOURNAL OF MANUFACTURING PROCESSES, 2018, 32 : 482 - 493
12345