Heat transfer in injection molding of crystalline plastics

被引：0
|
作者：
Bai, Yu [1 ]
Yin, Bo [2 ]
Fu, Xia-Rong [1 ]
Yang, Min-Gbo [2 ]
机构：
[1] College of Chemical Engineering, Sichuan University, Chengdu, 610065 Sichuan, China
[2] College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, 610065 Sichuan, China
来源：
Journal of Applied Polymer Science | 2006年 / 102卷 / 03期
关键词：
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Journal article (JA)
引用
收藏
页码：2249 / 2253
相关论文
共 50 条
  • [41] Simulation of microstructure development in injection molding of engineering plastics
    Yu, Jeong S.
    Wagner, Alan H.
    Kalyon, Dilhan M.
    Journal of Applied Polymer Science, 1992, 44 (03): : 477 - 489
  • [42] Development of Bio-Based Plastics for Injection Molding
    Takayama, Terufumi
    Komabayasi, Kentaro
    Itou, Masafumi
    Miyake, Yuichi
    SAE INTERNATIONAL JOURNAL OF MATERIALS AND MANUFACTURING, 2009, 2 (01) : 12 - 17
  • [43] Injection Molding of Amorphous Plastics Exemplified by PS.
    Oertel, H.
    Schleith, O.
    Kunststoffe - German Plastics, 1977, 67 (10): : 562 - 566
  • [44] Experimental Investigation of Injection Molding of Wood/Plastics Composites
    Behravesh, A. H.
    Aghdam, A. Zohdi
    Soury, E.
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2010, 29 (03) : 456 - 465
  • [45] Mechanism of weld line formation in injection molding of plastics
    A. V. Enikeev
    Yu. V. Kazankov
    V. A. Mironov
    Chemical and Petroleum Engineering, 1999, 35 : 118 - 123
  • [46] PRODUCTIVITY IMPROVEMENT IN INJECTION-MOLDING OF ENGINEERING PLASTICS
    MOELTGEN, B
    KUNSTSTOFFE-GERMAN PLASTICS, 1985, 75 (01): : 19 - 24
  • [47] Heat transfer in injection molding for reproduction of sub-micron-sized features
    Nakao, M.
    Tsuchiya, K.
    Sadamitsu, T.
    Ichikohara, Y.
    Ohba, T.
    Ooi, T.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2008, 38 (3-4): : 426 - 432
  • [48] Heat transfer in injection molding for reproduction of sub-micron-sized features
    M. Nakao
    K. Tsuchiya
    T. Sadamitsu
    Y. Ichikohara
    T. Ohba
    T. Ooi
    The International Journal of Advanced Manufacturing Technology, 2008, 38 : 426 - 432
  • [49] Heat transfer in injection molding for reproduction of sub-micron-sized features
    Nakao, M.
    Tsuchiya, K.
    Sadamitsu, T.
    Ichikohara, Y.
    Ohba, T.
    Ooi, T.
    International Journal of Advanced Manufacturing Technology, 2008, 38 (3-4): : 426 - 432
  • [50] Improvement of heat transfer analytical models for thermoplastic injection molding and comparison with experiments
    Pignon, Baptiste
    Sobotka, Vincent
    Boyard, Nicolas
    Delaunay, Didier
    INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2018, 118 : 14 - 26
12345