Formation mechanism of WCp/Ti-6Al-4V graded metal matrix composites layer produced by laser melt injection

被引：3

作者：

Chen, Yanbin ^{[1
]}

Liu, Dejian ^{[1
]}

Li, Liqun ^{[1
]}

Li, Fuquan ^{[1
]}

Chen, Shuhai ^{[1
]}

机构：

[1] State Key Laboratory of Advanced Welding Production Technology, Harbin Institute of Technology

来源：

Zhongguo Jiguang/Chinese Journal of Lasers | 2008年 / 35卷 / 11期

关键词：

Graded metal matrix composites; Laser melt injection; Laser technique;

D O I：

10.3788/CJL20083511.1718

中图分类号：

学科分类号：

摘要：

WCp/Ti-6Al-4V graded metal matrix composites (MMC) layer was produced by the laser melt injection (LMI) process and the formation mechanism of the graded layer was studied. The results show that the initial speed of the particle (v0), the minimum velocity of injected particles necessary for penetrating through the melt surface (vmin) and the viscosity of the melt pool (η) play key roles in the distribution of the WC particle. With big density, the WC particle has high kinetic energy during the laser melt injection process, and therefore the viscosity of the melt pool is not a critical factor anymore. The solidification front of the solid-liquid interface of the melt pool is the most sensitive factor that determines the formation of the graded layer when the WC particle is used as injection particle. Meanwhile, the total amount of WC particle at different depth of the MMC layer is dominated by the length of the solidification front in this depth. The injection location plays an important role in the distribution of WC particles. When the WC particles are injected into the extended part of melt pool, the depth of this region is low, and the WC particles meet the solidification front at higher position. In that case, most WC particles are trapped at the top part of the melt pool and therefore a WCp/Ti-6Al-4V graded metal matrix composites layer is formed.

引用

页码：1718 / 1722

页数：4

共 17 条

[1]

Suresh S., Graded materials for resistance to contact deformation and damage, Science, 292, 29, pp. 2447-2451, (2001)

[2]

Ding H., Dai Z., Fretting wear characteristics of titanium alloy in sea water, Rare Metal Materials and Engineering, 36, 5, pp. 778-781, (2007)

[3]

Zhang W., Liu Z., Study on microstructure of in-situ synthesis of TiC-Cr7C3-Ti-Ni metal-ceramics composite coating, Chinese J. Lasers, 35, 7, pp. 1091-1094, (2008)

[4]

Wang W., Sun Y., Dai Z., Et al., Third-order optical nonlinearity and preparation of Au-BaTiO3 composite films by pulsed laser deposition, Acta Optica Sinica, 26, 8, pp. 1265-1268, (2006)

[5]

Xu B., Lou B., Bai W., Et al., Synthesis of SiC/Ni composite coatings by laser cladding and property of erosion resistance, Chinese J. Lasers, 35, 1, pp. 147-150, (2008)

[6]

Wang W., Chao M., Wang D., Et al., Investigation on in-situ synthesis of TaC particulate reinforced ni-based composite coatings by laser cladding, Chinese J. Lasers, 34, 4, pp. 277-282, (2007)

[7]

Liu D., Chen Y., Li F., Et al., WC particulate reinforced metal matrix composites layers produced by laser melt injection, Chinese J. Lasers, 35, 7, pp. 1083-1086, (2008)

[8]

Huang Y., Yang Y., Wei G., Et al., Boundary coupled dual-equation numerical simulation on the mass transfer in the process of laser cladding, Chin. Opt. Lett., 6, 5, pp. 356-360, (2008)

[9]

Pei Y.T., Ocelik V., de Hosson J.Th.M., SiCp/Ti6Al4V functionally graded materials produced by laser melt injection, Acta Materialia, 50, 8, pp. 2035-2051, (2002)

[10]

Liu D.J., Li L.Q., Li F.Q., Et al., WCp/Fe metal matrix composites produced by laser melt injection, Surface and Coating Technology, 202, 9, pp. 1771-1777, (2008)

← 1 2 →