Ballistic test of double-layer metal casing of aero-engines

被引：0
|
作者：
Zhang F. [1 ]
Cao Z. [1 ]
Miao Y. [2 ]
Cong P. [2 ]
Bai S. [2 ]
Zhang D. [1 ]
机构：
[1] School of Science, Nanjing University of Science and Technology, Nanjing
[2] Shenyang Engine Research Institute, Aero Engine Corporation of China, Shenyang
来源：
Hangkong Dongli Xuebao/Journal of Aerospace Power | 2022年 / 37卷 / 06期
关键词：
ANSYS/LS-DYNA numerical simulation; ballistic limit; ballistic test; dimensionless target thickness; double-layer TC4 laminated target plates; gaps; penetration;
D O I：
10.13224/j.cnki.jasp.20210115
中图分类号：
学科分类号：
摘要：
In order to study the containment of double-layer metal-structured casing of aeroengines under blade`s impact, the ballistic test of double-layer titanium alloy laminated target plates with different clearances was carried out by using a sliding-bore gun test system . The process of blade penetration into target plate was recorded by high-speed camera system, and the damaged targets were recovered. The penetration resistance and failure modes of different laminated target plates were studied. Through 28 effective ballistic tests, it was found that： compared with the test results of the combination with the same thickness of the inner （attack surface）and outer target plate, the larger gap indicated the worse anti-penetration ability of the target plate； compared with the test results of the combination without the gap, the anti-penetration ability of the combination with the thinner inner target plate was better than that of the combination with the same thickness of the inner and outer target plates. The ballistic test was simulated numerically by commercial finite element software ANSYS/LS-DYNA. The finite element simulation results were in good agreement with the test results. It was found that the anti-penetration ability of the combination with thinner inner target was stronger than that of the combination with thicker inner target, and both of them were stronger than that of the combination with the same thickness of inner and outer targets； in the case of no clearance, the ballistic limit increased with the increase of blade angle of attack, but the angle of attack of the sudden increase of velocity curve was different. The dimensionless target thickness determined the failure mode of the blade impacting the double-layer targets. © 2022 BUAA Press. All rights reserved.
引用
收藏
页码：1248 / 1259
页数：11
相关论文
共 25 条
  • [11] ROSENBERG Z, DEKEL E., Terminal ballistics, (2012)
  • [12] DENG Y, ZHANG W, CAO Z., Experimental investigation on the ballistic resistance of monolithic and multi-layered plates against ogival-nosed rigid projectiles impact, Materials & Design, 44, pp. 228-239, (2013)
  • [13] DENG Y, ZHANG W, CAO Z., Experimental investigation on the ballistic resistance of monolithic and multi-layered plates against hemispherical-nosed projectiles impact, Materials & Design, 41, pp. 266-281, (2012)
  • [14] DEY S, BORVIK T, TENG X, Et al., On the ballistic resistance of double-layered steel plates:an experimental and numerical investigation[J], International Journal of Solids and Structures, 44, 20, pp. 6701-6723, (2007)
  • [15] WOODWARD R L, CIMPOERU S J., A study of the perforation of aluminium laminate targets[J], International Journal of Impact Engineering, 21, 3, pp. 117-131, (1998)
  • [16] BORVIK T, FORRESTAL M J, HOPPERSTAD O S, Et al., Perforation of AA5083-H116 aluminium plates with conical-nose steel projectiles-calculations[J], International Journal of Impact Engineering, 36, 3, pp. 426-437, (2009)
  • [17] BEN-DOR G, DUBINSKY A, ELPERIN T., On the ballistic resistance of multi-layered targets with air gaps[J], International Journal of Solids & Structures, 35, 23, pp. 3097-3103, (1998)
  • [18] YANG Shuanglin, Simulated containment test and numerical simulation of double-layered metal casing, (2010)
  • [19] pp. 76-81, (2000)
  • [20] GUPTA N K, IQBAL M A, SEKHON G S., Effect of projectile nose shape, impact velocity and target thickness on the deformation behavior of layered plates[J], International journal of impact engineering, 35, 1, pp. 37-60, (2008)
123