Experimental study on the shear behavior of a bolt connector in a steel-concrete composite beam

被引：0

作者：

Yang Y. ^{[1
,2
]}

Zhang S. ^{[1
]}

Chen X. ^{[1
]}

Feng S. ^{[1
]}

Yang S. ^{[1
]}

机构：

[1] School of Civil Engineering, Xi′an University of Architecture and Technology, Xi′an

[2] Key Lab of Structural Engineering and Earthquake Resistance, Ministry of Education, Xi′an

来源：

Harbin Gongcheng Daxue Xuebao/Journal of Harbin Engineering University | 2024年 / 45卷 / 06期

关键词：

bolt connector; construction performance; push-out test; shear behavior; shear capacity; shear stiffness; slip; steel-concrete composite beam;

D O I：

10.11990/jheu.202203013

中图分类号：

学科分类号：

摘要：

The diameter of a traditional bolt connector is smaller than that of the predrilled holes in a steel beam, resulting in a gap between the bolt and the hole wall, possibly causing a relative slip between the steel beam and the concrete slab on the top, thereby increasing the deflection of the combined beams. To minimize or eliminate the above mentioned gaps, the reamer and threaded hole bolts are introduced as the shear connectors of composite structures, and the cone sleeve self-lock bolt connectors are proposed. Eight push-out tests were designed and implemented on the bolt connectors. According to the load-slip curve of each specimen, the specific differences in shear mechanical properties, such as shear-bearing capacity, slip capacity, and shear stiffness between three types of bolt connectors and traditional bolt connectors, were studied, showing that the failure modes of the three bolt connector types are consistent with those of the traditional bolt connectors. These failure modes are the shear failure of the bolt rod, and the concrete around the bolt has no peeling phenomenon. All three bolt connectors are similar to traditional bolt connectors in terms of shear-bearing capacity. According to the load-slip curve of the specimen, these three bolt connectors can be divided into elastic, elastic-plastic, and failure stages. The ductility coefficient and shear stiffness of the three bolt connectors are better than those of the traditional bolts. Considering the mechanical properties, construction performance, and economy, reamed bolt connectors should be used as the shear connectors of composite structures. © 2024 Editorial Board of Journal of Harbin Engineering. All rights reserved.

引用

页码：1076 / 1084

页数：8

共 27 条

[1]

NIE Jianguo, YU Zhiwu, Research and practice of composite steel-concrete beams in China, China civil engineering journal, 32, 2, pp. 3-8, (1999)

[2]

(2005)

[3]

FAN Jiansheng, NIE Jianguo, Progress in research and application of composite steel-concrete bridges, Progress in steel building structures, 8, 5, pp. 35-39, (2006)

[4]

ZONG Zhouhong, CHE Huimin, Experimental study of shear connector under static and fatigue loading, Journal of Fuzhou University (natural sciences edtion), 27, 6, pp. 61-66, (1999)

[5]

LIN Zhaofei, LIU Yuqing, HE Jun, Research on calculation method of shear stiffness for headed stud connectors, Engineering mechanics, 31, 7, pp. 85-90, (2014)

[6]

XUE Weichen, DING Min, WANG Hua, Et al., Experimental studies on behavior of stud shear connectors under monotonic loads, Journal of building structures, 30, 1, pp. 95-100, (2009)

[7]

DALLAM L N., High strength bolt shear connectors-pushout tests, ACI journal proceedings, 65, 9, pp. 767-769, (1968)

[8]

KWON G, ENGELHARDT M D, KLINGNER R E., Behavior of post-installed shear connectors under static and fatigue loading, Journal of constructional steel research, 66, 4, pp. 532-541, (2010)

[9]

KWON G, ENGELHARDT M D, KLINGNER R E., Experimental behavior of bridge beams retrofitted with postinstalled shear connectors, Journal of bridge engineering, 16, 4, pp. 536-545, (2011)

[10]

KWON G, ENGELHARDT M D, KLINGNER R E., Parametric studies and preliminary design recommendations on the use of postinstalled shear connectors for strengthening noncomposite steel bridges, Journal of bridge engineering, 17, 2, pp. 310-317, (2012)

← 1 2 3 →