Parameter Model and Experimental Verification of Controllable Laser Preparation of Dry Gas Seal Surface Groove

被引：0
|
作者：
Wang Y. [1 ]
Kong K. [1 ]
He Y. [1 ]
Wang Y. [1 ]
Liu Y. [1 ]
Zhao Q. [2 ]
机构：
[1] School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang
[2] Nanjing Cuizhi Laser Application Technology Research Institute Co. ，Ltd, Nanjing
来源：
Hunan Daxue Xuebao/Journal of Hunan University Natural Sciences | 2023年 / 50卷 / 10期
基金：
中国国家自然科学基金; 中国博士后科学基金;
关键词：
dry gas seal; efficient preparation; groove depth; laser processing; processing technology; roughness;
D O I：
10.16339/j.cnki.hdxbzkb.2023181
中图分类号：
学科分类号：
摘要：
To address the difficulty in controlling groove depth and roughness during micron-level groove machining of dry gas seals，a theoretical evaluation method was proposed，and a model was constructed to investigate the machining depth and roughness. Using this numerical simulation，the relationships between the laser fill spacing S and spot diameter ds，and the resulting groove depth ha and roughness Ras were systematically investigated. The results demonstrate that the groove depth and roughness decrease with the increasing filling spacing，and the influence on groove depth and roughness is significant when S < 7 μm. The effect of spot diameter on the groove depth is insignificant，the roughness initially increased slowly and then rapidly with the increase in spot diameter，and the critical value of ds was approximately 7 μm. The experimental results well supported those of the numerical analysis of groove depth，which was slightly different from the results of roughness analysis. In this study，the TOPSIS comprehensive evaluation method was used to optimize the optimal range of the processing parameters：considering the processing efficiency，the optimal parameter ranges are 8 μm ≤ S ≤ 15 μm and 9 μm ≤ ds ≤ 15 μm；however，when the processing efficiency is not considered，the optimal parameter ranges are 5 μm ≤ S ≤ 10 μm and 5 μm ≤ ds ≤ 15 μm. The research results have certain guiding significance for further improving the high efficiency and precision machining of micron-level groove depth of dry gas seal. © 2023 Hunan University. All rights reserved.
引用
收藏
页码：142 / 150
页数：8
相关论文
共 18 条
  • [11] HALPERIN G．, Analytical and experimental investigation of laser-textured mechanical seal faces ［J］．, Tribology Transactions, 42, 3, pp. 511-516, (1999)
  • [12] CHICHKOV B N，, MOMMA C，, NOLTE S, Femtosecond，picosecond and nanosecond laser ablation of solids［J］, Applied Physics A, 63, 2, pp. 109-115, (1996)
  • [13] GAI X C．, Research on experimental system and technique of femtosecond laser micromachining［D］．Harbin：Harbin Institute of Technology, pp. 34-46, (2013)
  • [14] MAO W Y, SONG P Y, DENG Q G, Research on laser processing technology of spiral groove for dry gas seal［J］, Advanced Engineering Sciences, 50, 5, pp. 253-262, (2018)
  • [15] MAO W Y, SONG P Y, DENG Q G, Optimization of laser processing technology for dry gas seal spiral groove based on ACE method［J］, Advanced Engineering Sciences, 53, 2, pp. 195-202, (2021)
  • [16] LIAO Y M, ZHOU J J., The theory and practice of laser induced electrochemistry technology［J］, Electromachining & Mould, 6, pp. 9-13, (1998)
  • [17] WANG Y, WANG Y Y，, XIAO Y F, Ultrafast laser precision machining of dry gas seal based on ordered texture design［J］, Materials Reports, 36, 5, pp. 44-52, (2022)
  • [18] SHI L L, Research on laser surface texturing parameters based on nanosecond laser processing technology［J］, Machine Building & Automation, 48, 6, pp. 11-13, (2019)
12