Parameter Model and Experimental Verification of Controllable Laser Preparation of Dry Gas Seal Surface Groove

被引：0
|
作者：
Wang Y. [1 ]
Kong K. [1 ]
He Y. [1 ]
Wang Y. [1 ]
Liu Y. [1 ]
Zhao Q. [2 ]
机构：
[1] School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang
[2] Nanjing Cuizhi Laser Application Technology Research Institute Co. ，Ltd, Nanjing
来源：
Hunan Daxue Xuebao/Journal of Hunan University Natural Sciences | 2023年 / 50卷 / 10期
基金：
中国国家自然科学基金; 中国博士后科学基金;
关键词：
dry gas seal; efficient preparation; groove depth; laser processing; processing technology; roughness;
D O I：
10.16339/j.cnki.hdxbzkb.2023181
中图分类号：
学科分类号：
摘要：
To address the difficulty in controlling groove depth and roughness during micron-level groove machining of dry gas seals，a theoretical evaluation method was proposed，and a model was constructed to investigate the machining depth and roughness. Using this numerical simulation，the relationships between the laser fill spacing S and spot diameter ds，and the resulting groove depth ha and roughness Ras were systematically investigated. The results demonstrate that the groove depth and roughness decrease with the increasing filling spacing，and the influence on groove depth and roughness is significant when S < 7 μm. The effect of spot diameter on the groove depth is insignificant，the roughness initially increased slowly and then rapidly with the increase in spot diameter，and the critical value of ds was approximately 7 μm. The experimental results well supported those of the numerical analysis of groove depth，which was slightly different from the results of roughness analysis. In this study，the TOPSIS comprehensive evaluation method was used to optimize the optimal range of the processing parameters：considering the processing efficiency，the optimal parameter ranges are 8 μm ≤ S ≤ 15 μm and 9 μm ≤ ds ≤ 15 μm；however，when the processing efficiency is not considered，the optimal parameter ranges are 5 μm ≤ S ≤ 10 μm and 5 μm ≤ ds ≤ 15 μm. The research results have certain guiding significance for further improving the high efficiency and precision machining of micron-level groove depth of dry gas seal. © 2023 Hunan University. All rights reserved.
引用
收藏
页码：142 / 150
页数：8
相关论文
共 18 条
  • [1] LIU J J．, Mechanism and structure of dry gas seals［J］, Journal of Chemical Industry & Engineering, 23, 4, pp. 38-39, (2002)
  • [2] WANG Y M, LIU W, LIU Y．, Current research and developing trends on non-contacting mechanical seals［J］, Hydraulics Pneumatics & Seals, 31, 2, pp. 29-33, (2011)
  • [3] SONG J．, Transient analysis and vibration suppression of dry gas seal friction, pp. 1-4, (2019)
  • [4] WANG Y, Current research on slotting technology of non-contact mechanical seal［J］, Hydraulics Pneumatics & Seals, 36, 11, pp. 1-6, (2016)
  • [5] FENG X Z，, PENG X D．, Effect of surface roughness on performance of a spiral groove gas seal ［J］, Lubrication Engineering, 31, 1, pp. 20-22, (2006)
  • [6] MAO W Y, SONG P Y, DENG Q G, A review on the study of the groove etched process for the hydrodynamic mechanical seals［J］, Lubrication Engineering, 42, 11, pp. 124-136, (2017)
  • [7] PENG X D, SHENG S E, Effect of surface roughness on performance prediction and geometric optimization of a spiral-groove face seal［J］．, Tribology, 27, 6, pp. 567-572, (2007)
  • [8] MAO W Y, SONG P Y, DENG Q G, Influence of surface roughness of spiral groove bottom on dry gas seal performance［J］, Lubrication Engineering, 42, 1, pp. 27-33, (2017)
  • [9] LI K F, SUN S Q, ZHOU B X．, Effects of shaft surface roughness and temperature on sealing performance of lip oil seal［J］, Fluid Machinery, 50, 3, pp. 26-33, (2022)
  • [10] BURSTEIN L．, A model for mechanical seals with regular microsurface structure［J］, Tribology Transactions, 39, 3, pp. 677-683, (1996)
12