Milling vibration suppression of thin-walled structure based on electromagnetic induction

被引：0
作者：
Yang, Yiqing [1 ]
Gong, Jiwen [1 ]
机构：
[1] School of Mechanical Engineering and Automation, Beihang University, Beijing
来源：
Zhendong Ceshi Yu Zhenduan/Journal of Vibration, Measurement and Diagnosis | 2015年 / 35卷 / 03期
关键词：
Electromagnetic induction; Milling; Thin-walled structure; Vibration suppression;
D O I：
10.16450/j.cnki.issn.1004-6801.2015.03.004
中图分类号：
学科分类号：
摘要：
There are many thin-walled structures in aircraft. Due to the low flexibility of structures, work-piece deformation and deflection occur easily during the machining, which causes low precision and low surface quality. Therefore, much has been done to investigate the machining process, deflection prediction and control technology of thin-walled structure machining. However, real application in the industry is still a challenge. In this paper, a vibration suppression device for the thin-walled structure is investigated and designed based on electromagnetic induction. The workpiece vibration is utilized in order to cause a change in the magnetic flux through the closed circuit, so the resulting magnetic force can contribute to the suppression of workpiece vibration. The magnetic force resulting from the movement of the magnet inside the copper tube is formulated. It is shown to vary linearly with workpiece velocity in the opposite direction. Impact tests show that the device can sharply attenuate the oscillation time, and the chatter stability simulation shows that the stability limit of the thin-walled workpiece is increased from 0.4 mm to 5.1 mm. Cutting tests are carried out to verify the final vibration suppression effect. ©, 2015, Nanjing University of Aeronautics an Astronautics. All right reserved.
引用
收藏
页码：429 / 433
页数：4
相关论文
共 12 条
  • [1] Qin G., Wu Z., Zhang W., Analysis and control technique of fixturing deformation mechanism of thin-walled workpieced, Chinese Journal of Mechanical Engineering, 43, 4, pp. 211-216, (2007)
  • [2] Aoyama T., Kakinuma Y., Development of fixture devices for thin and compliant workpieces, CIRP Annals-Manufacturing Technology, 54, 1, pp. 325-328, (2005)
  • [3] Shamoto E., Mori T., Nishimura K., Et al., Suppression of regenerative chatter vibration in simultaneous double-sided milling of flexible plates by speed difference, CIRP Annals-Manufacturing Technology, 59, 1, pp. 387-390, (2010)
  • [4] Ratchev S., Liu S., Becker A.A., Error compensation strategy in milling flexible thin-wall parts, Journal of Materials Processing Technology, 162-163, pp. 673-681, (2005)
  • [5] Budak E., Mechanics and dynamics of milling thin walled structures, (1994)
  • [6] Liang R., Ye W., Stability prediction for high-speed milling of thin walled structures and experimental validation, Journal of Mechanical Engineering, 45, 11, pp. 146-151, (2009)
  • [7] Dohner J.L., Lauffer J.P., Hinnerichs T.D., Mitigation of chatter instabilities in milling by active structural control, Journal of Sound and Vibration, 269, 1-2, pp. 197-211, (2004)
  • [8] Rashid A., Nicolescu C.M., Active vibration control in palletised workholding system for milling, International Journal of Machine Tools and Manufacture, 46, 12-13, pp. 1626-1636, (2006)
  • [9] Duncan G.S., Tummond M.F., Schmitz T.L., An investigation of the dynamic absorber effect in high-speed machining, International Journal of Machine Tools and Manufacture, 45, 4-5, pp. 497-507, (2005)
  • [10] Rashid A., Nicolescu C.M., Design and implementation of tuned viscoelastic dampers for vibration control in milling, International Journal of Machine Tools and Manufacture, 48, 9, pp. 1036-1053, (2008)
12