Microstructure and mechanical properties of M62 high-speed steel powder consolidated by high-temperature gas extrusion

被引：6

作者：

Sivaprahasam D. ^{[1
]}

Chandrasekhar S.B. ^{[1
]}

Murugan K. ^{[1
]}

Prabhakar K.V.P. ^{[1
]}

机构：

[1] International Advanced Research Centre for Powder Metallurgy and New Materials, Hyderabad

来源：

Sivaprahasam, D. (sprakash@arci.res.in) | 1600年 / Taylor and Francis Ltd.卷 / 24期

关键词：

hardness; heat treatment; high speed tool steel; High–temperature gas extrusion; microstructure;

D O I：

10.1080/14328917.2019.1580889

中图分类号：

学科分类号：

摘要：

Super high-speed steel (AISI M62) powder was consolidated using high-temperature gas extrusion (HTGE). Consolidation of powder at 1200°C and 400 MPa pressure using HTGE resulted in 99.6% density while conventional extrusion (CE), at the same parameters resulted in 93% density. Variations in hardness with heat treatment were studied with respect to its microstructure, carbide size and distribution. The rods extruded using HTGE and CE and subsequently heat treated showed average matrix grain size of 1.6±0.5 µm and 6.0±2.0 µm along with homogeneous distribution of carbides of size 0.56 ± 0.31 μm and 1.52±0.68 μm, respectively. Such an ultrafine-grained microstructure obtained in HTGE resulted in a hardness of 950±20 HV (>68 HRC) in the quenched and tempered condition, which is the highest ever reported hardness value so far for this system, while CEed sample showed a hardness of only 756±18 HV (~62 HRC) under the same conditions. © 2019, © 2019 Informa UK Limited, trading as Taylor & Francis Group.

引用

页码：52 / 57

页数：5

共 22 条

[1]

Davis J.R., ASM speciality hand book: tool materials, pp. 26-30, (1995)

[2]

Kirk F.A., Problems in high-speed manufacture and use: a challenge for economic powder metallurgy processing, Powder Metall, 24, pp. 70-74, (1981)

[3]

Niu H.J., Chang I.T.H., Microstructural evolution during laser cladding of M2 high-speed steel, Metall Mater Trans A, 31, pp. 2615-2625, (2000)

[4]

Wright C.S., Ogel B., Lemoisson F., Et al., Super solidus sintering of high speed steels: part 2: sintering of tungsten based alloys, Powder Metall, 38, pp. 221-229, (1995)

[5]

Zhou G.L., Wood J.V., Influence of alloying elements on mechanical properties of sintered high speed steel powders diluted with highly compressible powder, Powder Metall, 38, pp. 230-236, (1995)

[6]

Dixon R.B., Stasko W., Pinnow K.E., Particle metallurgy tool steels, powder metal technologies and applications, 7, pp. 786-802, (1998)

[7]

Mesquita R.A., Barbosa C.A., evaluation of as hipped PM high speed steel for production of large diameter cutting tools, advanced powder technology III, book series, Mater Sci Forum, 416-4, pp. 235-240, (2003)

[8]

Gimenez S., Zubizarreta C., Trabadelo V., Et al., Sintering behaviour and microstructure development of T 42 powder metallurgy high speed steel under different processing conditions, Mater Sci Eng A, 480, pp. 130-137, (2008)

[9]

Wright C.S., Youseffi M., Wronski A.S., Et al., Super solidus liquid phase sintering of high speed steels: part 3: computer aided design of sinterable alloys, Powder Metall, 42, pp. 131-146, (1999)

[10]

Wright C.S., Wronski A.S., Iturriza I., Development of robust processing routes for powder metallurgy high speed steels, Mater Sci Technol, 16, pp. 945-957, (2000)

← 1 2 3 →