Effects of laser remelting on wear resistance of Ni-WC composite coatings by flame-spraying

被引：2
作者：
School of Material Science and Engineering, Jiangsu University, Zhenjiang 212013, China [1 ]
不详 [2 ]
不详 [3 ]
机构：
[1] School of Material Science and Engineering, Jiangsu University
[2] Jiangsu Key Laboratory of Oil and Gas Storage and Transportation Technology, Jiangsu Polytechnic University
[3] Department of Mechanical Engineering, Jiangsu Polytechnic University
来源：
Zhongguo Jiguang | 2008年 / 2卷 / 281-286期
关键词：
Flame spraying; Laser remelting; Laser technique; Volume fraction; Wear resistance;
D O I：
10.3788/CJL20083502.0281
中图分类号：
学科分类号：
摘要：
Ni-WC composite coatings prepared by flame spraying were remelted with CO2 laser, and the morphologies of the composite coatings by laser remelting were observed with scanning electron microscopy (SEM). The micro-hardness (HV) of samples with the different volume fraction of WC particle was tested, and the effects of WC particles on microstructure and wear resistance were analyzed. It is shown that the coating pores prepared by flame spraying increase with the content of WC particle, and the pores are reduced obviously after laser remelting; The coating hardness after laser remelting increases 20% than that by flame spraying, which attains the biggest when WC volume fraction is 6%; The coating resistance wear after laser remelting increases with the increase of WC content. The best wear resistance is obtained when the WC volume fraction is as high as 6%.
引用
收藏
页码：281 / 286
页数：5
相关论文
共 16 条
  • [1] Si S., Xu K., Yuan X., Microstructure and wear performance of laser cladding Cr<sub>3</sub>C<sub>2</sub>/Co alloy composite coating, Tribology, 26, 2, pp. 125-129, (2006)
  • [2] Chen Y., Ren Z., A study of processing Cu/WC<sub>p</sub> composite coalings by laser cladding, Transactions of the China Welding Institution, 23, 1, pp. 19-22, (2002)
  • [3] Li Q., Chen Y., Lei T., Microstructure and dry sliding wear of laser clad WCp/Ni-Cr-B-Si-C alloy composite coatings, Chinese J. Lasers, A26, 2, pp. 186-192, (1999)
  • [4] Jiang Z., Xi S., Li H., Research and development trends of plasma sprayed ceramic coating by laser rcmelting, Journal of Materials Engineering, 44, 1, pp. 46-48, (1999)
  • [5] Niu X., Chao M., Zhou X., Research on in-situ synthesis of B<sub>4</sub>C particulate reinforced Ni-based composite coalings by laser cladding, Chinese J. Lasers, 32, 11, pp. 1583-1588, (2005)
  • [6] Hu J., Li D.Y., Llewellyn R., Computational investigation of micro structural effects on abrasive wear of composite materials, Wear, 259, pp. 6-17, (2005)
  • [7] Wang H., Xia W., Jin Y., Study on abrasive resistance of Ni-based coatings containing WC hard phase, Tribology, 15, 3, pp. 211-217, (1995)
  • [8] Liu Q., Zhu W., Zou L., Microstructure and character of friction and wear of WCp/Ni based alloy gradient composite coating by wide-band laser cladding, Acta Material Composite Sinica, 19, 6, pp. 52-56, (2002)
  • [9] Li X., Li D., Zhou H., Analysis and prevention of porosities in flame spray welding of nickel-based alloys coating, Welding, 38, 1, pp. 29-31, (2004)
  • [10] Merrick S.T., Miller R.F., Advances in Thermal Spraying, pp. 633-635, (1986)
12