Mechanical and magnetic properties of polylactide-cobalt ferrite nanocomposite for 3D printing

被引：0
|
作者：
Ershov, P. [1 ]
Salnikov, V. [1 ]
Vorontsov, P. [1 ]
Omelyanchik, A. [1 ]
Amirov, A. [1 ]
Zhansitov, A. [2 ]
Musov, Kh. [2 ]
Khashirova, S. [2 ]
Senatov, F. [3 ]
Raikher, Yu. [1 ,4 ]
Rodionova, V. [1 ]
机构：
[1] Immanuel Kant Baltic Fed Univ, Kaliningrad 236000, Russia
[2] Kabardino Balkarian State Univ, Nalchik, Russia
[3] Natl Univ Sci & Technol MISIS, Leninskiy Pr 4, Moscow 119049, Russia
[4] Russian Acad Sci, Inst Continuous Media Mech, Ural Branch, Perm 614018, Russia
来源：
MATERIALS LETTERS | 2025年 / 382卷
基金：
俄罗斯科学基金会;
关键词：
IMPACT;
D O I：
10.1016/j.matlet.2024.137913
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this study, we employed fused deposition modeling (FDM) to fabricate polylactide (PLA) composites with 5 wt% and 10 wt% of CoFe2O4 (CFO) magnetic nanoparticles. The structural, mechanical, and magnetic properties of these nanocomposites were studied. Tensile testing revealed that as the concentration of CFO increased, both the tensile strength, from 26 MPa to 7 MPa, and deformation limits, from 4 % to 1 %, decreased. However, atomic force microscopy analysis showed an increase in the average Young's modulus of the surface. The results of magnetic measurements demonstrated that 3D technique enables one to controllably print the patterns which serve as the sources of local magnetic fields of complex geometries.
引用
收藏
页数：4
相关论文
共 50 条
  • [21] Determination of mechanical properties of materials used for 3D printing
    Sedlak J.
    Chladil J.
    Cerny M.
    Polzer A.
    Varhanik M.
    Dobrocky D.
    Joska Z.
    Pokorny Z.
    1600, J. E. Purkyne University in Usti nad Labem (20): : 190 - 194
  • [22] Adaptive 3D Printing for In Situ Adjustment of Mechanical Properties
    Lee, Wonchul
    Fritsch, Joshua
    Maqsood, Ahmed
    Liu, Shawn
    Bourassa, Tomas
    Calara, Ron
    Kim, Woo Soo
    ADVANCED INTELLIGENT SYSTEMS, 2023, 5 (01)
  • [23] Investigation of the Printability and Mechanical Properties of 3D Printing UHPC
    Bai G.
    Wang L.
    Wang F.
    Cheng X.
    Cailiao Daobao/Materials Reports, 2021, 35 (12): : 12063 - 12069
  • [24] Effect of environment on mechanical properties of 3D printed polylactide for biomedical applications
    Moetazedian, Amirpasha
    Gleadall, Andrew
    Han, Xiaoxiao
    Silberschmidt, Vadim V.
    JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS, 2020, 102
  • [25] The influence of nanostructure on the mechanical properties of 3D printed polylactide/nanoclay composites
    Paspali, Antigoni
    Bao, Yuqing
    Gawne, David T.
    Piestert, Frederik
    Reinelt, Sebastian
    COMPOSITES PART B-ENGINEERING, 2018, 152 : 160 - 168
  • [26] Soft ferrite 3D printing of magnetic couplers of inductive power transfer systems
    Hu, Meilin
    Madawala, Udaya Kumara
    Diegel, Olaf
    IET POWER ELECTRONICS, 2024, 17 (15) : 2179 - 2191
  • [27] Technology for Processing Composite Materials Based on Polylactide Using 3D Printing: Properties and Structure
    Timofeeva, N. F.
    Lazareva, N. N.
    Okhlopkova, A. A.
    Kapitonova, Yu. V.
    Tobonova, T. I.
    THEORETICAL FOUNDATIONS OF CHEMICAL ENGINEERING, 2024, : 702 - 707
  • [28] 3D Printing of ABS Barium Ferrite Composites
    Hanemann, Thomas
    Syperek, Diana
    Noetzel, Dorit
    MATERIALS, 2020, 13 (06)
  • [29] Recycling potential of MWCNTs/HDPE nanocomposite filament: 3D printing and mechanical characterization
    Kumar, Sumodh
    Ramesh, M. R.
    Doddamani, Mrityunjay
    JOURNAL OF MATERIAL CYCLES AND WASTE MANAGEMENT, 2023, 25 (02) : 1168 - 1178
  • [30] Recycling potential of MWCNTs/HDPE nanocomposite filament: 3D printing and mechanical characterization
    Sumodh Kumar
    M. R. Ramesh
    Mrityunjay Doddamani
    Journal of Material Cycles and Waste Management, 2023, 25 : 1168 - 1178
12345