Effect of solidified shell on level characteristics in continuous casting slab molds for high speed casting

被引：0

作者：

Deng, Xiao-Xuan ^{[1
]}

Huang, Qi ^{[2
]}

Wang, Xin-Hua ^{[2
]}

Li, Lin-Ping ^{[2
]}

Ji, Chen-Xi ^{[1
]}

Zhu, Guo-Sen ^{[1
]}

机构：

[1] Shougang Technology Research Center, Shougang Corporation, Beijing

[2] School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing

来源：

Beijing Keji Daxue Xuebao/Journal of University of Science and Technology Beijing | 2014年 / 36卷 / 09期

关键词：

Continuous casting; High speed; Molds; Solidified shell; Water modeling;

D O I：

10.13374/j.issn1001-053x.2014.09.017

中图分类号：

学科分类号：

摘要：

A full scale water model of continuous casting was built to investigate the effect of solidified shell on fluid flow and level characteristics under high speed casting. It is found that a slight asymmetry of fluid flow occurs in the model with solidified shell. Furthermore, the average level fluctuation and the meniscus velocity of the mold with solidified shell is 31% and 35% larger than those without solidified shell at a high casting speed of 2.4 m·min-1, respectively. The deformation of the top level profile of the mold with solidified shell is also larger than that without solidified shell, which can be vulnerable to slag entrapment. In addition, the fast Fourier transformation analysis of level oscillation shows that the amplitude of high frequency fluctuation in the mold with solidified shell is larger than that without solidified shell due to a narrower space in the lower part of the mold, indicating that a more turbulence energy exists in the upper recirculation zone than that without solidified shell and thus results in a higher level fluctuation and a larger surface velocity. So taking solidified shell into consideration is necessary to minimize the difference between the model and actual steel casters.

引用

页码：1247 / 1254

页数：7

共 20 条

[1] Wada T., Suzuki H., Mori T., High speed casting of 3 meters/minute on the NKK Fukuyama Works' No. 5 slab caster, Iron Steelmaker, 14, (1987)
[2] Suzuki M., Suzuki M., Nakada M., Perspectives of research on high-speed conventional slab continuous casting of carbon steels, 41, 7, (2001)
[3] Shirayama A., Kubota J., Mori T., Et al., Technique for high speed casting of No 5 CCM at Fukuyama Works, 52, (1988)
[4] Bao Y.P., Zhu J.Q., Jiang W., Et al., Water modeling research on slag-entrapment in the mould of thin slab continuous caster, 21, 6, (1999)
[5] Deng X.X., Wang Q.Q., Qian L., Et al., Water model optimization of three-port submerged entry nozzle feeding a funnel-shaped thin slab mold, Iron Steel, 47, 7, (2012)
[6] Zhang L.F., Yang S., Cai K., Et al., Investigation of fluid flow and steel cleanliness in the continuous casting strand, 38, 1, (2007)
[7] Thomas B., Mika L., Najjar F., Simulation of fluid flow inside a continuous slab-casting machine, 21, 2, (1990)
[8] Wilson F.G., Heesom M.J., Nicholson A., Et al., Effect of fluid flow characteristics on nozzle blockage in aluminium-killed steels, Ironmaking Steelmaking, 14, 6, (1987)
[9] Najjar F., Thomas B., Hershey D., Numerical study of steady turbulent flow through bifurcated nozzles in continuous casting, 26, 4, (1995)
[10] Deng X.X., Xiong X., Wang X.H., Et al., Effect of nozzle bottom shapes on level fluctuation and meniscus velocity in high-speed continuous casting molds, 36, 4, (2014)

← 1 2 →