Research on the calculation method for the deformation capacity of RC shear walls with a flange

被引：0
|
作者：
Wang B. [1 ,2 ,3 ]
Shi Q.-X. [1 ,2 ,3 ]
Cai W.-Z. [2 ]
Peng Y.-G. [2 ]
Li H. [2 ]
机构：
[1] State Key Laboratory of Green Building in Western China, Xi'an University of Architecture & Technology, Xi'an
[2] School of Civil Engineering, Xi'an University of Architecture & Technology, Xi'an
[3] Key Laboratory of Structural Engineering and Seismic Resistance Education, Xi'an University of Architecture & Technology, Xi'an
来源：
Gongcheng Lixue/Engineering Mechanics | 2020年 / 37卷 / 03期
关键词：
Calculation model; Deformation analysis; Deformation capacity; Quasi-static test; Reinforced concrete; T-shaped wall;
D O I：
10.6052/j.issn.1000-4750.2019.04.0219
中图分类号：
学科分类号：
摘要：
Through quasi-static tests on three T-shaped reinforced concrete shear walls, the proportion of each deformation component and its variation in the loading process were analyzed. Based on the experimental observation and a moment-curvature analysis, a method for calculating the flexural deformation of the wall panel was established by using the plastic hinge model with the change of the equivalent plastic hinge height taken into consideration. A method for calculating the deformation caused by the slip of longitudinal bars was established by modifying the slip model by Lowes. A method for calculating the shear deformation was established based on the linear relationship between the shear strain and curvature. Accordingly, a new load-deformation analysis model including the contributions of flexural, slip and shear deformations was proposed. The good agreement between the analytical and experimental results confirmed the validity of the proposed model. The research shows that the proposed model not only has a clear determination on each deformation component, but also can accurately estimate the story drift and the deformations at any height. Furthermore, the proposed model is applicable to shear walls with different cross sections, and provides an effective analysis method for the performance design and performance evaluation, which can be used as a reference for engineering design. © 2020, Engineering Mechanics Press. All right reserved.
引用
收藏
页码：167 / 175and216
相关论文
共 24 条
  • [1] Dang Z., Liang X., Deng M., Deformation capacity analysis of fiber concrete shear wall considering axial-flexure-shear interaction, Engineering Mechanics, 31, 1, pp. 113-121, (2014)
  • [2] Xu L., Xiao S., Lu X., Et al., Damage evolution anslysis of RC shear wall based on nonlinear combination of deformation and hysteretic energy, Engineering Mechanics, 34, 8, pp. 117-124, (2017)
  • [3] Paulay T., Priestley M.J.N., Stability of ductile structural walls, ACI Structural Journal, 90, 4, pp. 385-392, (1993)
  • [4] Huang Z., Lu X., Zhou Y., Deformation capacity and performancebased seismic design for reinforced concrete shear walls, Earthquake Engineering and Vibration, 29, 5, pp. 86-92, (2009)
  • [5] Qian J., Xu F., Displacement-based deformation capacity method of cantilever walls, Journal of Tsinghua University (Science and Technology), 47, 3, pp. 305-308, (2007)
  • [6] Park R., Paulay T., Reinforced Concrete Structures, (1975)
  • [7] Zhang S., Lu X., Zhang H., Experimental and analytical studies on the ultimate displacement of RC shear walls, China Civil Engineering Journal, 42, 4, pp. 10-16, (2009)
  • [8] Liang X., Zheng Y., Deng M., Et al., An investigation of deformation behavior of the shear wall with fiber reinforced concrete in plastic hinge region, Engineering Mechanics, 30, 3, pp. 256-262, (2013)
  • [9] Thomsen J.H., Wallace J.W., Displacement-based Design of RC Structural Walls: Experimental Studies of Walls With Rectangular and T-shaped Cross Sections, (1995)
  • [10] Beyer K., Dazio A., Priestley M.J.N., Quasi-static cyclic tests of two U-shaped reinforced concrete walls, Journal of Earthquake Engineering, 12, 7, pp. 1023-1053, (2008)
123