Al3(Sc, Zr) precipitation in deformed Al-Mg-Mn-Sc-Zr alloy: Effect of annealing temperature and dislocation density

被引：47

作者：

Jiang J. ^{[1
]}

Jiang F. ^{[1
,2
,3
]}

Zhang M. ^{[1
]}

Tang Z. ^{[2
]}

Tong M. ^{[1
]}

机构：

[1] School of Material Science and Engineering, Central South University, Changsha

[2] Light Alloy Research Institute, Central South University, Changsha

[3] The National Key Laboratory of Science and Technology for National Defence on High-Strength Lightweight Structural Materials, Central South University, Changsha

来源：

Journal of Alloys and Compounds | 2020年 / 831卷

关键词：

Al[!sub]3[!/sub](Sc; Zr); particle; Annealing; Coherency loss; Equal channel angular pressing; Recrystallization;

D O I：

10.1016/j.jallcom.2020.154856

中图分类号：

学科分类号：

摘要：

The changes of Al3(Sc, Zr) morphology in deformed Al-Mg-Mn-Sc-Zr alloy were studied. Two experiment conditions were designed: different temperature and different dislocation density. Different dislocation density was obtained by different deformation method (traditional hot extrusion and equal channel angular pressing (ECAP)). It is calculated that the ECAP introduced a large amount of dislocations into the alloy and these dislocations accelerated the recrystallization making the interfaces move drastically. It is found that annealing the extruded sample at for 1 h does not cause the loss of coherency of the Al3(Sc, Zr) particles whether under 450 °C or 550 °C. However, annealing the ECAP sample at 450 °C causes a small amount of the particles loss of coherency. The main reason is that the grain boundary cut through the particle. Annealing the ECAP sample at 550 °C would cause most of the particles to lose coherency, and there are three main types of incoherency. © 2020 Elsevier B.V.

引用

共 48 条

[1]

Sukiman N.L., Gupta R.K., Zhang R., Buchheit R.G., Influence of microalloying additions on Al-Mg alloy. Part 2: phase analysis and sensitisation behavior, Corrosion Eng. Sci. Technol., 49, pp. 263-268, (2014)

[2]

Wen S.P., Xing Z.B., Huang H., Li B.L., Wang W., Nie Z.R., The effect of erbium on the microstructure and mechanical properties of Al–Mg–Mn–Zr alloy, Mater. Sci. Eng., 516, pp. 42-49, (2009)

[3]

Alil A., Popovic M., Radetic T., Zrilic M., Romhanji E., Influence of annealing temperature on the baking response and corrosion properties of an Al–4.6 wt% Mg alloy with 0.54 wt% Cu, J. Alloys Compd., 625, pp. 76-84, (2015)

[4]

Lathabai S., Lloyd P.G., The effect of scandium on the microstructure, mechanical properties and weldability of a cast Al–Mg alloy, Acta Mater., 50, pp. 4275-4292, (2002)

[5]

Zhou S., Zhang Z., Li M., Pan D., Wu Y., Effect of Sc on microstructure and mechanical properties of as-cast Al–Mg alloys, Mater. Des., 90, pp. 1077-1084, (2016)

[6]

Norman A.F., Prangnell P.B., McEwen R.S., The solidification behaviour of dilute aluminium–scandium alloys, Acta Mater., 46, pp. 5715-5732, (1998)

[7]

Zhemchuzhnikova D., Kaibyshev R., Mechanical behavior of an Al–Mg–Mn–Sc alloy with an ultrafine grain structure at cryogenic temperatures, Adv. Eng. Mater., 17, pp. 1804-1811, (2015)

[8]

Kumar N., Mishra R.S., Additivity of strengthening mechanisms in ultrafine grained Al–Mg–Sc alloy, Mater. Sci. Eng., 580, pp. 175-183, (2013)

[9]

Liu F.C., Xue P., Ma Z.Y., Microstructural evolution in recrystallized and unrecrystallized Al–Mg–Sc alloys during superplastic deformation, Mater. Sci. Eng., 547, pp. 55-63, (2012)

[10]

Apps P.J., Berta M., Prangnell P.B., The effect of dispersoids on the grain refinement mechanisms during deformation of aluminium alloys to ultra-high strains, Acta Mater., 53, pp. 499-511, (2005)

← 1 2 3 4 5 →