Analysis on the forming limit of cold open-die extrusion with mandrel for the thick-walled tube

被引：0

作者：

Zhang S. ^{[1
,2
]}

Li Q. ^{[1
,2
]}

Wang L. ^{[2
]}

Gao Y. ^{[2
]}

Li Z. ^{[2
]}

Li J. ^{[3
]}

机构：

[1] College of Mechanical Engineering, Yanshan University

[2] College of Materials Science and Engineering, Hebei University of Science and Technology

[3] The President's Office, Hebei Polytechnic University

来源：

Jixie Gongcheng Xuebao/Journal of Mechanical Engineering | 2010年 / 46卷 / 22期

关键词：

Forming limit; Open-die cold extrusion with mandrel; Optimal die cone angle; Stream function; Upper bound theory;

D O I：

10.3901/JME.2010.22.053

中图分类号：

学科分类号：

摘要：

The forming of open-die extrusion with mandrel for the thick walled tube is of low material consumption and high efficiency compared with the traditional cutting. An analysis on the forming characteristics of the mandrel open-die cold extrusion is performed and the main influence parameters of the forming limit are defined. Continuous velocity field of the deformation zone is established by using stream function method, the theoretical model of forming limit is obtained by using upper bound theory. By programming calculation and analysis, the effect of various parameters (the original blank thickness to diameter ratio, friction coefficient, die cone angle) on the forming limit is put forward. With the increase of die angle, the limit reduction (forming limit) first increases and then decreases, i.e. the limit reduction has a maximum and obtains the optimal die angle in the range of 15°~20°. With the increase of friction coefficient, the limit reduction decreases. Comparing the theoretical calculation result with the experimental result shows that the error is less than 8%, which meets the engineering requirement. The research contents and results have important guiding function in mapping out the process of thick-walled tube open-die cold extrusion forming with mandrel. © 2010 Journal of Machanical Engineering.

引用

页码：53 / 57

页数：4

共 11 条

[1] Liu L., Qin J., New technology of thick wall tube of sleeve-like part, China Metalforming Equipment & Manufacturing Technology, 4, pp. 50-52, (2004)
[2] Ahmetogue M., Altan T., Tube hydroforming research and practical application, Journal of Materials Processing Technology, 98, 3, pp. 25-27, (2003)
[3] Li J., Research on open-die cold extrusion forming's modelling and its technological parameters application, (1997)
[4] Li J., Han P., Theoretical and experimental study on maximum reduction of open-die cold extrusion, Journal of Plasticity Engineering, 2, 7, pp. 31-34, (2000)
[5] Li S., Zhang L., Liu Y., The flow function upper bound modes and its applications in extrusion, Materials Science and Technology, 7, 2, pp. 27-33, (1999)
[6] Liu X., The study on the forming limit of tube parts formed by open-die cold extrusion, (2008)
[7] Kudo H., An upper-bound approach to plane strain forging and extrusion, Engineering for Industry, 2, 10, pp. 10-18, (1960)
[8] Mamalis A.G., Petrossian G.L., Manolakos D.E., Open-die forging of sintered cylindrical billets an analytical approach, Journal of Materials Processing Technology, 5, 16, pp. 112-116, (2004)
[9] Hu M., Wu X., Hydrodynamics, (2008)
[10] Zhang S., Mao H., Li J., Et al., Theoretical and experimental research on the forming limit of deep tine taper hole formed by open-die cold extrusion, Journal of Plasticity Engineering, 6, pp. 47-49, (2004)

← 1 2 →