Experiment study on filling imbalance phenomenon of melt front during injection molding process

被引：3
|
作者：
Jiang, Kaiyu [1 ]
Yokoi, Hidetoshi [2 ]
机构：
[1] Key Laboratory for Precision and Non-Traditional Machining Technology, Dalian University of Technology, Dalian 116023, China
[2] Center for Collaborative Research, University of Tokyo, Tokyo 153-8505, Japan
来源：
Jixie Gongcheng Xuebao/Journal of Mechanical Engineering | 2009年 / 45卷 / 02期
关键词：
D O I：
10.3901/JME.2009.02.294
中图分类号：
学科分类号：
摘要：
引用
收藏
页码：294 / 300
相关论文
共 50 条
  • [1] Control of polymer melt flow front position during the injection molding process
    Speight, RG
    Hull, JB
    Coates, PD
    ANTEC '96: PLASTICS - RACING INTO THE FUTURE, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPACIAL AREAS, 1996, 42 : 588 - 592
  • [2] Visualization experiment for the impact of scale effect on filling imbalance of injection molding
    Jiang, Kaiyu
    Tian, Jingna
    Ma, Jiajia
    Wang, Minjie
    Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering, 2011, 27 (11): : 122 - 125
  • [3] Visualization experiment of the filling behavior of composite materials during injection molding process
    Jiang, Kaiyu
    Duan, Fei
    Tian, Jingna
    Wang, Minjie
    Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering, 2012, 28 (11): : 129 - 132
  • [4] Numerical Investigation on the Effect of Pressure and Temperature on the Melt Filling During Injection Molding Process
    M. S. Rusdi
    M. Z. Abdullah
    A. S. Mahmud
    C. Y. Khor
    M. S. Abdul Aziz
    Z. M. Ariff
    M. K. Abdullah
    Arabian Journal for Science and Engineering, 2016, 41 : 1907 - 1919
  • [5] Numerical Investigation on the Effect of Pressure and Temperature on the Melt Filling During Injection Molding Process
    Rusdi, M. S.
    Abdullah, M. Z.
    Mahmud, A. S.
    Khor, C. Y.
    Aziz, M. S. Abdul
    Ariff, Z. M.
    Abdullah, M. K.
    ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2016, 41 (05) : 1907 - 1919
  • [6] The study on polymer melt front, gas front and solid layer in filling stage of gas-assisted injection molding
    Shen, YK
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2001, 28 (01) : 139 - 148
  • [7] Macroscopic and mesoscopic simulation of polystyrene melt in the filling process of injection molding
    Liu, Qingsheng
    Liu, Youqiong
    Jiang, Chuntao
    JOURNAL OF APPLIED POLYMER SCIENCE, 2023, 140 (29)
  • [8] Computational Analysis of Polymer Melt Filling in a Medical Mold Cavity During the Injection Molding Process
    Abdullah, Muhammad Khalil
    Rusdi, Mohd Syakirin
    Abdullah, Mohd Zulkifly
    Mahmud, Abdus Samad
    Ariff, Zulkifli Mohamad
    Yee, Khor Chu
    Mokhtar, Mohd Najib Ali
    PERTANIKA JOURNAL OF SCIENCE AND TECHNOLOGY, 2023, 31 (01): : 33 - 49
  • [9] Experimental and numerical study of the melt behavior during the injection molding process
    Ilinca, F
    Hétu, JF
    Derdouri, A
    MATERIALS PROCESSING AND DESIGN: MODELING, SIMULATION AND APPLICATIONS, PTS 1 AND 2, 2004, 712 : 157 - 162
  • [10] Analysis of Melt Front Behavior of a Light Guiding Plate during the Filling Phase of Micro-Injection Molding
    Lin, Wei-Chun
    Fan, Fang-Yu
    Huang, Chiung-Fang
    Shen, Yung-Kang
    Wang, Liping
    POLYMERS, 2022, 14 (15)
12345