Effect of sintering temperature on microstructure and mechanical properties of WMoTaVTi refractory high entropy alloys

被引：0

作者：

Yang, Yihan ^{[1
]}

Han, Yong ^{[1
]}

Tang, Sisi ^{[1
]}

Li, Yuan ^{[1
]}

Yuan, Yuan ^{[1
]}

Jiang, Xue ^{[1
]}

Liu, Ying ^{[2
]}

机构：

[1] State Key Laboratory of Powder Metallurgy, Central South University, Changsha

[2] Zijin Mining Renewable Energy and Advanced Materials(Changsha) Co. Ltd., Changsha

来源：

Zhongnan Daxue Xuebao (Ziran Kexue Ban)/Journal of Central South University (Science and Technology) | 2024年 / 55卷 / 08期

基金：

中国国家自然科学基金;

关键词：

mechanical properties; microstructure; refractory high entropy alloys(RHEAs); spark plasma sintering(SPS);

D O I：

10.11817/j.issn.1672-7207.2024.08.008

中图分类号：

学科分类号：

摘要：

Refractory high entropy alloys(RHEAs) have broad application prospect in ultra-high temperature filed such as aerospace because of its high service temperature and excellent thermal stability. However, RHEAs are facing the problems of insufficient comprehensive mechanical properties and further application is limited. In order to solve these problems, a kind of WMoTaVTi RHEA was prepared by introducing Ti element on the basis of WMoTaV RHEA, and the effect of sintering temperature on sintering densification, microstructure and mechanical properties of WMoTaVTi RHEAs were systematically investigated. The results show that the grain size of the alloy increases gradually and the yield strength of the alloy increases first and then decreases with the increase of sintering temperature. When the sintering temperature is 1 500 ℃, the alloy exhibits the optimal comprehensive properties at room temperature and its relative density exceeds 99%, with compressive yield strength of 1 672 MPa and a fracture strain of 16.6%, and the fracture morphology is mainly intergranular fracture. Compared with WMoTaV RHEA, the yield strength of WMoTaVTi RHEA increases by 18%. Through the multi-dimensional analysis, due to the introduction of a small amount of O into the powder metallurgy process, the alloy mainly consists of BCC matrix phase and a small amount of TiO precipitation phase with FCC structure. With the increase of sintering temperature, the solid solubility of the matrix increases, and the volume fraction of TiO phase decreases gradually. The improvement of strength can be attributed to the solid solution strengthening and precipitation strengthening. © 2024 Central South University of Technology. All rights reserved.

引用

页码：2940 / 2950

页数：10

共 37 条

[21]

GAO Fei, LI Shuangming, LI Kewei, Formation of non-equilibrium ductile solid solutions and textures in NbCr2 bulks produced by mechanical milling and spark plasma sintering, Journal of Alloys and Compounds, 826, (2020)

[22]

LI Da, DONG Yaguang, ZHANG Zhiqing, Et al., An as-cast TiVCrAl light-weight medium entropy alloy with outstanding tensile properties, Journal of Alloys and Compounds, 877, (2021)

[23]

HU Xin, LIU Xinli, YAN Dingshun, Et al., A high-density non-equiatomic WTaMoNbV high-entropy alloy: alloying behavior, microstructure and mechanical properties, Journal of Alloys and Compounds, 894, (2022)

[24]

KANG B, KONG T, RYU H J, Et al., Superior mechanical properties and strengthening mechanisms of lightweight AlxCrNbVMo refractory high-entropy alloys(x=0, 0.5, 1.0) fabricated by the powder metallurgy process, Journal of Materials Science and Technology, 69, 10, (2021)

[25]

MORAVCIKOVA-GOUVEA L, MORAVCIK I, OMASTA M, Et al., High-strength Al0.2Co1.5CrFeNi1.5Ti high-entropy alloy produced by powder metallurgy and casting: a comparison of microstructures, mechanical and tribological properties, Materials Characterization, 159, (2020)

[26]

ZHANG Lin, LI Xingyu, QU Xuanhui, Et al., Powder metallurgy route to ultrafine-grained refractory metals, Advanced Materials, 35, 50, (2023)

[27]

XU Tong, CHEN Qingjun, ZHENG Zuodong, Et al., Research progress in composition design and properties of high entropy alloys, Materials Research and Application, 17, 6, (2023)

[28]

GAO Fei, SUN Yu, HU Lianxi, Et al., Microstructure and strengthening mechanisms of novel lightweight TiAlV0.5 CrMo refractory high-entropy alloy fabricated by mechanical alloying and spark plasma sintering, Journal of Alloys and Compounds, 932, (2023)

[29]

HAMPL M, SCHMID-FETZER R., Thermodynamic description of the Ti-O system, International Journal of Materials Research, 106, 5, (2015)

[30]

CHEN Jie, PENG Fang, WANG Yipeng, Et al., Mechanisms and mechanical properties of high-temperature high-pressure sintered vanadium carbide ceramics, International Journal of Refractory Metals & Hard Materials, 118, (2024)

← 1 2 3 4 →