Effects of C content on the microstructure and properties of CoCrFeNiTi0.5Mo0.5Cx high-entropy alloy coatings by laser cladding

被引：3

作者：

Lin, Tianxiang ^{[1
]}

Feng, Meiyan ^{[1
]}

Lian, Guofu ^{[1
]}

Lu, Hua ^{[2
]}

Chen, Changrong ^{[1
]}

Huang, Xu ^{[1
]}

机构：

[1] School of Mechanical and Automotive Engineering, Fujian University of Technology, Fuzhou

[2] School of Humanities, Fujian University of Technology, Fuzhou

来源：

Journal of Materials Research and Technology | 2024年 / 33卷

关键词：

Corrosion resistance; High-entropy alloys; Laser cladding; Microhardness; Microstructure; Wear resistance;

D O I：

10.1016/j.jmrt.2024.09.126

中图分类号：

学科分类号：

摘要：

In order to deeply investigate the influence mechanism of different contents of non-metallic element C on the microstructure, microhardness, wear resistance and corrosion resistance of high-entropy alloy coatings. CoCrFeNiTi0.5Mo0.5Cx high-entropy alloy coating was prepared on the surface of AISI 1045 steel by laser cladding technology. The results show that the microstructure of CoCrFeNiTi0.5Mo0.5 without C addition consists of FCC phase, BCC phase, intermetallic compound phase and σ-phase structure, and the carbide phases (M7C3 and TiC) start to appear after the addition of C element. The microhardness of the coating increases and then decreases with the increase of C content, and the average hardness is the highest when x = 0.03, 495.3HV0.5, which is 27.6% higher than that of C0. The abrasion resistance of the CoCrFeNiTi0.5Mo0.5Cx high-entropy alloy coatings is gradually increased and then decreased with the increase of C content, and the wear amount decreases from 0.0813 mm3 to 0.0514 mm3, and the main frictional wear mechanisms are adhesive wear, abrasive wear and oxidative wear. With the increase of C content, the corrosion resistance of the coating is gradually improved and then reduced, when the C content is 0.03, the highest corrosion potential is −0.818V, the lowest corrosion current is 1.382E-4 A/cm2, at this time, the passivation film on the surface of the coating is the most stable and dense, with the best corrosion resistance. The results of this paper provide a theoretical reference for the effect of adding non-metallic elements on the microstructure and properties of high-entropy alloy coatings. © 2024 The Authors

引用

页码：1540 / 1557

页数：17

共 76 条

[31]

Xiao J.-K., Tan H., Chen J., Et al., Effect of carbon content on microstructure, hardness and wear resistance of CoCrFeMnNiCx high-entropy alloys, J Alloys Compd, 847, (2020)

[32]

Wei X., Zhang L., Zhang F., Et al., Effect of carbon addition on the microstructure and corrosion resistance of the CoCrFeNi high-entropy alloy, Corrosion Sci, 231, (2024)

[33]

Ma Q., Zhang H., Lv Y., Et al., Microstructure and properties of W0.5Ta0.3MoNbVAlTi1-xZrx high entropy alloy coatings by laser cladding on the surface of 45# steel, Ceram Int, 49, 22, pp. 36416-36428, (2023)

[34]

Feng M., Lin T., Lian G., Et al., Effects of Nb content on the microstructure and properties of CoCrFeMnNiNbx high-entropy alloy coatings by laser cladding, J Mater Res Technol, 28, pp. 3835-3848, (2024)

[35]

Chen Z.B., Zhang G.G., Chen J.J., Et al., Microstructure and wear property of WMoTaNb refractory high entropy alloy coating by laser cladding, J Mater Res Technol, 28, pp. 1557-1569, (2024)

[36]

Qin G., Xue W., Fan C., Et al., Effect of Co content on phase formation and mechanical properties of (AlCoCrFeNi)100-xCox high-entropy alloys, Mater Sci Eng, A, 710, pp. 200-205, (2018)

[37]

Fu Z., Chen W., Wen H., Et al., Effects of Co and sintering method on microstructure and mechanical behavior of a high-entropy Al0.6NiFeCrCo alloy prepared by powder metallurgy, J Alloys Compd, 646, pp. 175-182, (2015)

[38]

Liu C., Peng W., Jiang C.S., Et al., Composition and phase structure dependence of mechanical and magnetic properties for AlCoCuFeNix high entropy alloys, J Mater Sci Technol, 35, 6, pp. 1175-1183, (2019)

[39]

Xiang C., Fu H.M., Zhang Z.M., Et al., Effect of Cr content on microstructure and properties of Mo0.5VNbTiCrx high-entropy alloys, J Alloys Compd, 818, (2020)

[40]

Stepanov N.D., Yurchenko N.Y., Skibin D.V., Et al., Structure and mechanical properties of the AlCrxNbTiV (x = 0, 0.5, 1, 1.5) high entropy alloys, J Alloys Compd, 652, pp. 266-280, (2015)

← 1 2 3 4 5 6 7 8 →