Friction and Wear Mechanism of Sliding Pairs for Incremental Launching Equipment

被引：0
|
作者：
Liang A. [1 ]
Bian Y. [1 ]
Shao J. [1 ]
Yang J. [1 ]
Liu G. [1 ]
机构：
[1] School of Mechanical Engineering, Tongji University, Shanghai
来源：
Tongji Daxue Xuebao/Journal of Tongji University | 2022年 / 50卷 / 06期
关键词：
0Cr18Ni9; stainless-steel; Coefficient of friction; Composite; Sliding pair of incremental launching equipment; Wear mechanism;
D O I：
10.11908/j.issn.0253-374x.21287
中图分类号：
学科分类号：
摘要：
In order to study the friction and wear performance of sliding pair of incremental launching equipment, a wear test-bed which can simulate the working process of incremental launching equipment is proposed. Tribological tests for the sliding pair composed of acrylonitrile butadiene styrene (ABS) and molybdenum disulfide (MoS2) reinforced polytetrafluorethylene (PTFE) and 0Cr18Ni9 stainless-steel were conducted on the wear test-bed. At different loads without lubrication, the variation of friction coefficient of friction pair was discussed and the wear mechanism of the friction pair was revealed. The microscopic and chemical composition of the worn surface for the sliding pairs were discussed by using scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). The results show that, with the increase of sliding times, the friction coefficient of the sliding pair first increases, then decreases, and finally stabileizes. Moreover, the initial value of friction coefficient at heavy load is larger than that at light load, but the final stable value is smaller than that at light load. At light load, the main wear mechanism is abrasive wear and adhesive wear. However, at heavy load, the main wear mechanism is adhesive wear and fatigue wear. © 2022, Editorial Department of Journal of Tongji University. All right reserved.
引用
收藏
页码：906 / 914
页数：8
相关论文
共 23 条
  • [1] HU Z, WU D, SUN L Z., Integrated investigation of an incremental launching method for the construction of long-span bridges, Journal of Constructional Steel Research, 112, (2015)
  • [2] GRANATA M F, MARGIOTTA P, ARICI M., A parametric study of curved incrementally launched bridges, Engineering Structures, 49, (2013)
  • [3] CHACON R, URIBE N, OLLER S., Numerical validation of the incremental launching method of a steel bridge through a small-scale experimental study, Experimental Techniques, 40, 1, (2016)
  • [4] WU X, WU T, CHEN W., Analysis of height difference between three trusses of a steel truss bridge during incremental launching, Stahlbau, 87, 9, (2018)
  • [5] GRANATA M F., Adjustable prestressing for construction stages of incrementally launched bridges, European Journal of Environmental and Civil Engineering, 19, 3, (2015)
  • [6] WANG J F, LIN J P, XU R Q., Incremental launching construction control of long multispan composite bridges, Journal of Bridge Engineering, 20, 11, (2015)
  • [7] SHAO C., Innovative structure design and construction-Jiubao Bridge, China, Structural Engineering International, 25, 1, (2015)
  • [8] BIAN Y, JIANG J, JING Z, Et al., Design and application of hydraulic-walking incremental launching equipment, Open Construction & Building Technology Journal, 7, 1, (2013)
  • [9] MOKHA A, CONSTANTINOU M, REINHORN A., Teflon bearings in base isolation I: testing, Journal of Structural Engineering, 116, 2, (1990)
  • [10] CONSTANTINOU M, MOKHA A, REINHORN A., Teflon bearings in base isolation II: modeling, Journal of Structural Engineering, 116, 2, (1990)
123