High-temperature Oxidation Behavior of Barrel Materials

被引：0

作者：

Zhang C. ^{[1
,2
]}

Zhang Y. ^{[2
]}

Wen X. ^{[1
]}

Bai P. ^{[1
]}

Meng Y. ^{[1
]}

Ma L. ^{[1
]}

Tian Y. ^{[1
]}

机构：

[1] State Key Laboratory of Tribology, Department of Mechanical Engineering, Tsinghua University, Beijing

[2] National Joint Engineering Research Center forAbrasion Control and Molding of Metal Materials, School of Materials Science and Engineering, Henan University of Science and Technology, Henan, Luoyang

来源：

Binggong Xuebao/Acta Armamentarii | 2024年 / 45卷 / 04期

关键词：

alloying element; barrel material; high-temperature oxidation; oxide layer;

D O I：

10.12382/bgxb.2022.0901

中图分类号：

学科分类号：

摘要：

With the increase in firepower strike requirements and the development of high-powered artillery, the high-temperature oxidation of barrel materials is becoming more and more serious, which seriously affects the performance of weapon and even leads to the scrapping of weapon. However, there is little research on the anti-oxidation performance of barrel materials at present. In this paper, the oxidation resistances and oxidation mechanisms of three barrel materials, i. e.,PCrNi3MoVA steel. 30SiMn2MoVA steel and MPS700 steel, at 600 ℃ in airare investigated. The cross-sectional morphology and phases of the oxide layers are analyzed by scanning electron microscopy, energy spectroscopy and X-ray diffractometry. The oxidation kinetics of three barrrel materials were analyzed. The results show that the oxide film thicknesses of the three steels gradually thicken and the rate of increaseinthickness gradually decreaseswith the increase in oxidation time. The oxidation kinetics curves of the three barrel materials are consistent with the parabolic growth kinetics law of oxide film. At 600 ℃, the internal oxide layer of PCrNi3MoVA steel forms an adhesive layer of a network structure consisting mainlyof Ni and Cr-richspinel oxides but theadhesive layerdoes not act as a barrier against oxidation. The inner layer of oxide layer of 30SiMn2MoVA steel is a porous aggregation zone of Si element oxide with a loose structure and relatively serious oxide flaking. The internal oxide layer of MPS700 steel forms a protective Cr-rich oxide layer that effectively prevents further oxidation. At the same time, Mo element stabilises the passivation film and indirectly improves oxidation resistance. Compared with PCrNi3MoVA steel and 30SiMn2MoVA steel, MPS700 steel can better form a dense oxidized layer under high temperature condition, so as to reduce the high temperature oxidation and wear degree of the matrix under high temperature conditions. MPS700 steel is more suitable for the preparation of long life and high reliability barrel. © 2024 China Ordnance Industry Corporation. All rights reserved.

引用

页码：1354 / 1362

页数：8

共 28 条

[1]

COTE P J, TODARO M, KENDALL G, Et al., Gun bore erosion mechanisms revisited with laser pulse heating [ J], Surface and Coatings Technology, 163, pp. 478-483, (2003)

[2]

ZHANG Z S, WU Y F., The analysis of the rubbing abrasion and erosion on the barrel bore, Journal of Academy of Armored Force Engineering, 2, pp. 70-73, (2003)

[3]

UNDERWOOD J H, TROIANO E., Critical fracture processes in army cannons: a review, Journal of Pressure Vessel Technology, 125, 3, pp. 287-292, (2003)

[4]

UNDERWOOD J H, VIGILANTE G N, MULLIGAN C P, Et al., Thermomechanically controlled erosion in army cannons: a review [ J], Journal of Pressure Vessel Technology, 128, 2, pp. 168-172, (2006)

[5]

JIN W Q, NING J G, WANG J, Et al., Simulation research of Interior ballistics based on erosion wear characteristic of full-bore [ J ], Acta Armamentarii, 40, 5, pp. 968-977, (2019)

[6]

LE G G, MA D W, FENG Y, Et al., Numerical simulation of muzzle blastflowfields of large caliber guns, Acta Armamentarii, 25, 1, pp. 19-22, (2004)

[7]

CHEN Y C, SONG Q Z, WANG J Z., New technologies to extend the erosion life of gun barrel, Acta Armamentarii, 27, 2, pp. 330-334, (2006)

[8]

WARRENDER J, MULLIGAN C, UNDERWOOD J., Analysis of thermo-mechanical cracking in refractory coatings using variable pulse-duration laser pulse heating [ J], Wear, 263, 7 - 12, pp. 1540-1544, (2007)

[9]

YU Z P., Technology research on laser hardening of gun tube bore surface, Journal of Ballistics, 13, 3, pp. 52-57, (2001)

[10]

WANG R, AN S M., Study of ablation resistance of non chromium plated firearm tubes treated by laser [ J], Journal of dalian university of technology, 2, pp. 102-106, (1997)

← 1 2 3 →