Fretting Wear Characteristics of Carbon Fiber Reinforced Epoxy Resin Matrix Composites in Low Temperature

被引：0

作者：

Xue C. ^{[1
]}

Yu M. ^{[1
]}

Yao J. ^{[2
]}

Ji K. ^{[1
]}

Dai Z. ^{[1
]}

机构：

[1] Institute of Bio-Inspired Structure and Surface Engineering of College of Astronautics, Nanjing University of Aeronautics and Astronautics, Nanjing

[2] Nanjing Bio-Inspired Technology Co., Nanjing

来源：

Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University | 2018年 / 52卷 / 05期

关键词：

Carbon fiber composites; Epoxy resin; Fretting wear; Low temperature; Wear mechanism;

D O I：

10.16183/j.cnki.jsjtu.2018.05.016

中图分类号：

学科分类号：

摘要：

The FTM200 friction and wear tester was used and the PH13-8Mo stainless steel was taken as the friction couple and an orthogonal experiment was applied to studying the influences of normal load, fretting frequency, fretting amplitude and test time on the tribological property of carbon fiber reinforced epoxy resin matrix composites at -45 ℃, -20 ℃ and room temperature. The results showed that normal load, fretting frequency, fretting amplitude, test time and temperature affected the friction coefficient very significantly. Friction coefficients of the samples at -45 ℃ were higher than that at room temperature, for the matrix was friable under low temperature and the components were peeled off more easily in the wear process, resulting in increase of wear rate. The influence of normal load and temperature on the wear of composite was more obvious. Under the same temperature, the wear volume of composite increased with the increase of the load. Under the same load, the wear volume of composite at -45 ℃ was larger than that at room temperature, indicating that the fretting and the spalling fatigue occurred more easily. At room temperature, the surface scratching of the composite and some cracks were mainly characterized. The fretting wear mechanism of the carbon fiber reinforced epoxy resin-based composites was abrasive wear and fatigue wear, while the wear mechanism of the material at low temperature mainly focused on fatigue wear. © 2018, Shanghai Jiao Tong University Press. All right reserved.

引用

页码：604 / 611

页数：7

共 10 条

[1]

Huang Y., Yuan C., Song S., Application of carbon fiber composites to cosmonautic fields, Science and Technology, 27, 26, (2017)

[2]

Jiang M., Fan Y., Analysis and prospect of domestic carbon fiber industry development, Advanced Materials Industry, 8, pp. 38-43, (2017)

[3]

Lin X., Zhu M., Zheng J., Et al., Fretting wear of micro-arc oxidation coating prepared on Ti6Al4V alloy, Transactions of Nonferrous Metals Society of China, 20, 4, pp. 537-546, (2010)

[4]

Gao X., Shang W., Gao Z., Et al., Design and research of carbon fiber reinforced friction materials, Materials Review, 29, 2, pp. 82-86, (2015)

[5]

Zhang R.L., Gao B., Du W.T., Et al., Enhanced mechanical properties of multiscale carbon fiber/epoxy composites by fiber surface treatment with graphene oxide/polyhedral oligomeric silsesquioxane, Composites Part A: Applied Science and Manufacturing, 84, pp. 455-463, (2016)

[6]

Yin Y., Liu Y., Ding G., Et al., Friction and wear properties of carbon fiber reinforced resin-based friction material, Aerospace Materials and Technology, 46, 2, pp. 31-35, (2016)

[7]

Liu X., Wu Z., He H., Et al., Cryogenic mechanical properties of unidirectional carbon fibers reinforced plastics, Acta Materiae Compositae Sinica, 34, 11, pp. 2437-2445, (2017)

[8]

Weng C., Research on cryogenic epoxy resin and carbon fiber fabric enhanced composite materials, (2012)

[9]

Dhieb H., Buijnsters J.G., Eddoumy F., Et al., Surface and sub-surface degradation of unidirectional carbon fiber reinforced epoxy composites under dry and wet reciprocating sliding, Composites Part A: Applied Science and Manufacturing, 55, pp. 53-62, (2013)

[10]

Xu X., Liu H., Zhu M., Et al., Study on high temperature fretting wear of Ti-Al-Zr alloy, Nuclear Power Engineering, 31, 5, pp. 42-47, (2010)

← 1 →