Determination of Holmquist-Johnson-Cook model parameters for sandstone

被引：0
|
作者：
Ling T. [1 ]
Wu S. [2 ]
Liu D. [1 ]
Liang S. [1 ]
Li C. [1 ]
Ma J. [1 ]
机构：
[1] School of Mechanics & Civil Engineering, China University of Mining and Technology(Beijing), Beijing
[2] China Institute of Water Resources and Hydropower Research, Beijing
来源：
| 2018年 / China Coal Society卷 / 43期
关键词：
Experimental measurement; HJC model; Numerical simulation; Sandstone; SHPB;
D O I：
10.13225/j.cnki.jccs.2017.1305
中图分类号：
学科分类号：
摘要：
HJC model has been widely used to describe the dynamic failure process of concrete. However, due to the reason that HJC model contains many parameters, the accurate determination on the parameters of HJC model for rock materials is a challenge. In this paper, the authors performed some laboratory experiments to determine the HJC parameters of sandstone samples that were collected from Weiyuan City, Sichuan, China. Specifically, the authors determined the elasticity modulus, Poisson's ratio, and uniaxial compressive strength of sandstone by uniaxial compression experiments, and the tensile strength by Brazilian disk splitting tests. The strength, strain rate, pressure and damage model constants were determined by fitting the HJC model to the experimental data obtained from the triaxial compression tests and uniaxial SHPB tests. The obtained HJC parameters were used to numerically simulate the SHPB tests of the sandstone samples using finite element program LS-DYNA. The results show that the stress-strain curve predicted by the HJC model is in good agreement with the experimental data. The mean error of dynamic peak stress and corresponding stain obtained by numerical simulation does not exceed 10%. This demonstrates the rationality and validity of the experimental method for determining the HJC parameters. © 2018, Editorial Office of Journal of China Coal Society. All right reserved.
引用
收藏
页码：2211 / 2216
页数：5
相关论文
共 18 条
  • [1] Holmquist T.J., Johnson G.R., A computational constitutive model for concrete subjected to large strains, high strain rates, and high pressures, 14th International Symposium on Ballistic, pp. 593-600, (1993)
  • [2] Ji C., Long Y., Wan W., Numerical simulation of projectile penetrating into steel fiber reinforced concrete, Journal of PLA University of Science and Technology, 6, 5, pp. 459-463, (2005)
  • [3] Han L., Gao S., Li M., Et al., Numerical studies on a projectile perforating concrete targets, Transactions of Beijing Institute and Technology, 26, 11, pp. 953-956, (2006)
  • [4] Jiang H., Wang J., Investigation on failure index of concrete in the projectile perforation simulation, Journal of Vibration and Shock, 28, 8, pp. 30-34, (2009)
  • [5] Meng Y., Wen H., Numerical simulation of the response of reinforced concrete slabs to projectile impact or explosive loading, Chinese Journal of High Pressure Physics, 25, 4, pp. 370-378, (2011)
  • [6] Zhang F., Li E., A method to determine the parameters of the model for concrete impact and damage, Journal of Ballistics, 13, 4, pp. 12-16, (2001)
  • [7] Chen J., Li X., Liu K., Experimental research on parameters of constitutive model for a cement mortar, Acta Scientiarum Naturalium Universitatis Pekinensis, 44, 5, pp. 689-694, (2008)
  • [8] Xiong Y., Hu Y., Xu J., Et al., Determining failure surface parameters of the Johnson-Holmquist concrete constitutive model, Acta Armamentarii, 31, 6, pp. 746-751, (2010)
  • [9] Xiong Y., Chen J., Hu Y., Et al., Study on the key parameters of the Johnson-Holmquist constitutive model for concrete, Engineering Mechanics, 29, 1, pp. 121-127, (2012)
  • [10] Sun Q., Li R., Zhao Y., Et al., Investigation on parameters of HJC model applied to Simulate perforation experiments of reinforced concrete, Engineering Mechanics, 33, 8, pp. 248-256, (2016)
12