Study on Non-Uniformity of Sub-Cooled Boiling Heat Transfer of High Pressure Water in Fuel Assembly

被引：0

作者：

Du L. ^{[1
]}

Chen X. ^{[1
,2
]}

Zhang P. ^{[3
]}

Zhang W. ^{[1
]}

Jin G. ^{[1
]}

机构：

[1] School of Energy and Power Engineering, Northeast Electric Power University, Jilin, 132012, Jilin

[2] China Resources Power Dengfeng Co. LTD., Dengfeng, 452473, Henan

[3] China Ship Development and Design Center, Wuhan

来源：

Hedongli Gongcheng/Nuclear Power Engineering | 2019年 / 40卷 / 04期

关键词：

Heat transfer characteristics; Non-uniformity; Sub-channel; Sub-cooled boiling;

D O I：

10.13832/j.jnpe.2019.04.0009

中图分类号：

学科分类号：

摘要：

Based on the VOF model in Fluent, a sub-cooled boiling model was established and was inserted by UDF code into the control equations. Sub-cooled boiling in the 5×5 rod bundles channel with spacer grid was simulated. Heat transfer characteristics in sub-channels were analyzed by investigating the void fraction distribution and the heat transfer characteristics of the fuel rods. The results show that the void fraction distribution is different even if the heating condition is the same, and the void fraction is larger in the edge channel than that in the angular channel. The analysis of the heat transfer characteristics around the rod shows that, the heat transfer of the direction of 0°, 90°, 180°, 270° of fuel rod is better, the x velocity is larger, and the boiling is stronger. © 2019, Editorial Board of Journal of Nuclear Power Engineering. All right reserved.

引用

页码：9 / 14

页数：5

共 9 条

[1]

Navarro M.A., Santos A.A.C., Evaluation of a numeric procedure for flow simulation of a 5×5 PWR rod bundle with a mixing vane spacer, Progress in Nuclear Energy, 53, 8, pp. 1190-1196, (2011)

[2]

Holloway M.V., Beastey D.E., Conner M.E., Single-phase convective heat transfer in rod bundles, Nuclear Engineering & Design, 238, 4, pp. 848-858, (2008)

[3]

Liu C.C., Ferng Y.M., Shih C.K., CFD evaluation of turbulence models for flow simulation of the fuel rod bundle with a spacer assembly, Applied Thermal Engineering, 40, 7, pp. 389-396, (2012)

[4]

Conner M.E., Baglietto E., Elmahdi A.M., CFD methodology and validation for single-phase flow in PWR fuel assemblies, Nuclear Engineering & Design, 240, 9, pp. 2088-2095, (2010)

[5]

Lo S., Osman J., CFD Modeling of Boiling Flow in PSBT 5×5 Bundle, Science and Technology and Nuclear Installations, 2012, 2012, pp. 1-5, (2012)

[6]

Jin Y., Smith L.D., Karoutas Z., Departure From Nucleate Boiling Modeling Development for PWR Fuel, International Conference on Nuclear Engineering, 7, (2013)

[7]

Bostjan K., Eckhard K., Dominique B., Et al., Two-Phase flow heat transfer in nuclear reactor systems, Science & Technology of Nuclear Installations, 2013, pp. 1-2, (2013)

[8]

Lee W.H., A pressure iteration scheme for two-phase flow modeling, Multiphase Transport: Fundamentals Reactor Safety, Applications, 1, pp. 407-431, (1980)

[9]

Wang H., Wang W.S., Bi Q.C., Experimental investigation on boiling heat transfer of high pressure water in a SCWR sub-Channel, International Journal of Heat and Mass Transfer, 105, pp. 799-810, (2017)

← 1 →