Design and Test of Hydraulic Proportional Flow Valve for Hydraulic Chassis in Tractor

被引：0
|
作者：
Li M. [1 ]
Ye J. [1 ]
Xie B. [2 ]
Yang S. [1 ]
Zeng B. [1 ]
Liu J. [1 ]
机构：
[1] College of Engineering and Technology, Southwest University, Chongqing
[2] College of Engineering, China Agricultural University, Beijing
来源：
Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery | 2018年 / 49卷 / 04期
关键词：
Hydraulic proportional flow valve; Test; Throttle; Tractor;
D O I：
10.6041/j.issn.1000-1298.2018.04.047
中图分类号：
学科分类号：
摘要：
In order to improve the speed stability of the hydraulic drive tractor and the ride comfort at low speed, a hydraulic proportional flow valve was designed. Pressure compensation function was used to eliminate the iMPact of pressure fluctuations on the flow. The structural parameters of the valve were designed by the method of traditional calculation and simulation. The simulation results showed that the flow rate range was 0~5.67×10-3 m3/s and the flow rate was changed smoothly with the change of control pressure; the flow rate control pressure zone accounted for 68.4% of the total control pressure range; the range of the compensation pressure was 0.3~0.7 MPa. The test results showed that the flow rate control pressure zone accounted for 45% of the total control pressure range when tractor was no-load and at idle engine speed; the flow rate control pressure zone accounted for 62% of the total control pressure range when tractor was no-load and at high engine speed; the flow rate control pressure zone accounted for 49.5% of the total control pressure range when tractor was high-duty and at idle engine speed; the flow rate control pressure zone accounted for 48.5% of the total control pressure range when tractor was high-duty and at high engine speed; the flow rate of the valve was stabilized at 8.33×10-5 m3/s when the control pressure was set to be 0.78 MPa and it was stabilized at 2.5×10-4 m3/s when the control pressure was set to be 0.84 MPa. © 2018, Chinese Society of Agricultural Machinery. All right reserved.
引用
收藏
页码：397 / 403
页数：6
相关论文
共 20 条
  • [1] Gao Q., Gao F., Tian L., Et al., Design and development of a variable ground clearance, variable wheel track self-leveling hillside vehicle power chassis, Journal of Terramechanics, 56, pp. 77-90, (2014)
  • [2] Wang B., Wang W., Wang M., Et al., Design and experiment of full hydraulic drive high clearance tracked vehicle, Transactions of the Chinese Society for Agricultural Machinery, 47, pp. 471-476, (2016)
  • [3] Hao Y., Quan L., Huang J., Research on the performance of electro-hydraulic proportional flow valve controlled by pilot pump, Journal of Mechanical Engineering, 52, 18, pp. 193-200, (2016)
  • [4] Qian J., Wei L., Zhang M., Et al., Flow rate analysis of compressible superheated steam through pressure reducing valves, Energy, 135, 15, pp. 650-658, (2017)
  • [5] Yang H., Cao J., Xu B., Et al., Progress in the evolution of directional control valves and future trends, Chinese Journal of Mechanical Engineering, 41, 10, pp. 1-5, (2005)
  • [6] Hong S.H., Kim K.W., A new type groove for hydraulic spool valve, Tribology International, 103, 12, pp. 629-640, (2016)
  • [7] Meng F., Shi P., Hamid R.K., Et al., Optimal design of an electro-hydraulic valve for heavy-duty vehicle clutch actuator with certain constraints, Mechanical Systems and Signal Processing, 68-69, pp. 491-503, (2016)
  • [8] Lisowski E., Filo G., Analysis of a proportional control valve flow coefficient with the usage of a CFD method, Flow Measurement and Instrumentation, 53, 3, pp. 269-278, (2016)
  • [9] Riccardo A., Elia D., Paolo T., Sliding spool design for reducing the actuation forces in direct operated proportional directional valves: experimental validation, Energy Conversion and Management, 119, 7, pp. 399-410, (2016)
  • [10] Wu W., Huang Q., Lou L., Simulation analysis and optimal design of hydraulic automatic reversing valve, Computer Simulation, 33, 12, pp. 220-224, (2016)
12