Fabrication of low density p-divinylbenzene foams

被引：0

作者：

Luo X. ^{[1
]}

Zhang L. ^{[1
]}

Du K. ^{[1
]}

Fang Y. ^{[1
]}

Yuan G. ^{[1
]}

机构：

[1] Research Center of Laser Fusion, CAEP, Mianyang 621900

来源：

Qiangjiguang Yu Lizishu/High Power Laser and Particle Beams | 2010年 / 22卷 / 01期

关键词：

High internal phase emulsion; Low density foams; Micro-machinability; P-divinylbenzene;

D O I：

10.3788/HPLPB20102201.0063

中图分类号：

学科分类号：

摘要：

In order to meet the requirement of low density micro-machinable CH foams in ICF, the fabrication of p-divinylbenzene foams by high internal phase emulsion(HIPE) have been introduced. The fabrication conditions were discussed, such as initiator, emulsifier, ratio of styrene and inorganic additive. Then the optimum formula was obtained. Characterization results of different density foams indicate that there are two different porous structures in foams: cells and wall holes. The cells have the diameter of 1~10 μm, and wall holes have the diameter of 0.2~2.0 μm. When the density of foams is 50 mg/cm3, the elastic module of foams is about 5 MPa. By the microfabrication, the foams with the density over 50 mg/cm3 could be machined to cylindrical and sliced targets used in ICF, whose minimum size can run up to 100 μm.

引用

页码：63 / 67

页数：4

共 10 条

[1]

Young A.T., Moreno D.K., Marsters R.G., Preparation of multishell ICF target plastic foam cushion materials by thermally induced phase inversion processes, J Vac Sci Technol, 20, 4, pp. 1094-1097, (1982)

[2]

Wang C., Mao Y., Luo X., Et al., Studied on thermodynamical properities in preparation of low density PMP foams, High Power Laser and Particle Beams, 13, 5, pp. 595-599, (2001)

[3]

Steckle W.P., Nobile A., Low density material for use in inertial fusion targets, Fusion Science and Technology, 43, 3, pp. 301-306, (2003)

[4]

Barby D., Haq Z., Low density porous cross-linked polymeric materials and their preparation and use as carriers for included liquids, (1985)

[5]

Williams J.M., Gray A.J., Wilkerson M.H., Emulsion stability and rigid foams from styrene or divinylbenzene water-in-oil emulsions, Langmuir, 6, pp. 437-444, (1990)

[6]

Steckle W.P., Smith M.E., Nobile A., Optimization of HIPE foams, Fusion Science and Technology, 45, 2, pp. 74-79, (2004)

[7]

Williams J.M., Wroblerb D.A., Spatial distribution of the phases in water-in-oil emulsions. Open and closed microcellular foams from cross-linked polystyrene, Langmuir, 4, 3, pp. 656-662, (1988)

[8]

Lissant K.J., Emulsions and Emulsion Technology: Part 1, (1974)

[9]

Pan Z., Polymer Chemistry, pp. 111-133, (2007)

[10]

Xu M., Shi Z., He B., Et al., Actal structure of macroporous crosslinked polystyrenes, Ion Exchange and Adsorption, 16, 5, pp. 385-391, (2000)

← 1 →