Finite element method for dynamic response in enclosed gear-driven system

被引：0

作者：

Han, Bin Hui ^{[1
,2
]}

Sun, Da Gang ^{[1
]}

Li, Zhan Long ^{[3
]}

Song, Yong ^{[1
]}

Zhang, Jian Guang ^{[2
]}

机构：

[1] College of Mechanical Engineering, Taiyuan University of Science and Technology, Taiyuan, 030024, Shanxi

[2] Tai Yuan Institute Co., Ltd. of China Coal Technology and Engineering Group, Taiyuan, 030006, Shanxi

[3] Xi’an University of Technology, Xi’an

来源：

Open Mechanical Engineering Journal | 2015年 / 9卷 / 01期

关键词：

Dynamic simulation; Enclosed gear drive; Finite element; Vibration test;

D O I：

10.2174/1874155X01509010140

中图分类号：

学科分类号：

摘要：

The theoretical solving of dynamic analysis on the enclosed gear-driven system is complicated, and only the surface vibration data can be tested in the experiment. In view of this, 3D modeling is carried out on a given secondary planet reducer to create a finite element model and perform finite element modal analysis. Via the modal test, the correctness of the simulation is verified. Also, ANSYS transient dynamics analysis (Full) is utilized and nonlinear factors (e.g., time-varying mesh stiffness, composite mesh error, gear backlash, and damping ratio etc.) are taken into account to make a comparison between dynamic simulation and bench test. Research results show that the first six natural frequencies in the finite element method (FEM) are quite approximate to test results, and the maximum error ratio is 8.12%, implying that the mode of vibration is identical. Moreover, the error is small between the results of the dynamic simulation and average acceleration of vibration in bench test, indicating that the vibration rules are basically consistent. Based on that, the next step is to acquire the vibration acceleration and gear ring meshing point’s stress variation curve at the input end and output end, which tally with the project’s actualities. Such a method helps to cover the test method’s shortages in analysis of internal vibration response. © Han et al.; Licensee Bentham Open.

引用

页码：141 / 149

页数：8

共 21 条

[1]

Faydor L., Alfonso F., Kenichi H., Design manufacture stress analysis and experimental tests of low-noise high endurance spiral bevel gears, Mechanism and Machine Theory, 41, pp. 83-118, (2006)

[2]

Xia X.R., Yang F.J., Meng C.J., Influences of hypoid gear quality on rear axle noise, Journal of Hefei University of Technology (Natural Science), 32, pp. 167-170, (2009)

[3]

Zhang J., Xie S.L., Xu P.M., Tong B.H., Elasto-statics analysis of spider reducer with small tooth number difference, Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 29, 24, pp. 49-55, (2013)

[4]

Xu Z.M., Shi F.Y., Yansong H., Peng H.D., Zhou W.L., Simulation on heat transfer characteristics of vehicle wheel reductor, Transactions of the CSAE, 27, 4, pp. 158-163, (2011)

[5]

Ozguven H.N., Houser D.R., Mathematical models used in gear dynamics-a review, Journal of Sound and Vibration, 121, 3, pp. 383-411, (1988)

[6]

Zoltan K., Resita S.A., Platforma C., An Overview of Mathematical Models Used in Gear Dynamics, RJAV, 4, 1, pp. 43-50, (2007)

[7]

Li F.Z., Tong S.G., Wang X.B., Dynamic Optimization Design for Working Device of Hydraulic Excavator Based on Modal Analysis, Transactions of the Chinese Society for Agricultural Machinery, 45, 4, pp. 28-36, (2014)

[8]

Kahrarman A., Free torsional vibration characteris tics of compound planetary gear sets, Mech. Mach. Theory, 36, 8, pp. 953-971, (2001)

[9]

Lu J.H., Zhu R.P., Jin G.H., Analysis of dynamic load sharing behavior in planetary gearing, Journal of Mechanical Engineering, 45, 5, pp. 85-90, (2009)

[10]

Xiao Z.M., Qin D.T., Wang J.H., Wu W.H., Chen L.F., Study on torsional dynamics of 3-stage planetary gears of main reducer used in driving cutterhead of shield tunnelling machine, China Mechanical Engineering, 21, 18, pp. 2176-2182, (2010)

← 1 2 3 →