Stochastic tool wear assessment in milling difficult to machine alloys

被引：0
作者：
Niaki, Farbod Akhavan [1 ]
Ulutan, Durul [2 ]
Mears, Laine [1 ]
机构：
[1] International Center for Automotive Research, Clemson University, Greenville, SC
[2] Mechanical Engineering Department, Bucknell University, Lewisburg, PA
来源：
International Journal of Mechatronics and Manufacturing Systems | 2015年 / 8卷 / 3-4期
基金：
美国国家科学基金会;
关键词：
Kalman filter; Milling; Particle filter; Tool wear;
D O I：
10.1504/IJMMS.2015.073090
中图分类号：
学科分类号：
摘要：
In the machining industry, maximising profit is intuitively a primary goal; therefore continuously increasing machining process uptime and consequently productivity and efficiency is crucial. Tool wear plays an important factor in both machining uptime and quality, and since tool failure is related to the surface quality and the dimensional accuracy of the end product, it is essential to quantify and predict this phenomenon with the best possible certainty. One of the most common ways of tool wear prediction is through the use of low cost spindle current sensing technology which is used to measure spindle power consumption in CNC machines and relate power increase to tool wear. In this work, two methods of stochastic filtering (i.e. Kalman and particle filter) were used in predicting tool flank wear in machining difficult-to-machine materials through spindle power consumption measurements. Results show a maximum of 15% average error in estimation, which indicates the good potential of using stochastic filtering techniques in estimating tool flank wear. In addition, the particle filter was used for online estimation of a spindle power model parameter with uniform and Gaussian mixture models as the initial probability density functions, and the evolution of this parameter to the true posterior density function over time was investigated. Copyright © 2015 Inderscience Enterprises Ltd.
引用
收藏
页码：134 / 159
页数：25
相关论文
共 35 条
  • [1] Akhavan Niaki F., Ulutan D., Mears L., In-process tool flank wear estimation in machining gamma-prime strengthened alloys using Kalman filter, 43rd North American Manufacturing Research Conference, (2015)
  • [2] Akhavan Niaki F., Ulutan D., Mears L., Parameter estimation using Markov chain Monte Carlo method in mechanistic modeling of tool wear during milling, ASME 2015 International Manufacturing Science and Engineering Conference, (2015)
  • [3] Altintas Y., Yellowley I., In-process detection of tool failure in milling using cutting force models, Journal of Manufacturing Science and Engineering, 111, 2, pp. 149-157, (1989)
  • [4] Andrieu C., De Freitas N., Doucet A., Jordan M.I., An introduction to MCMC for machine learning, Machine Learning, 50, 1-2, pp. 5-43, (2003)
  • [5] Arulampalam M.S., Maskell S., Gordon N., Clapp T., A tutorial on particle filters for online nonlinear/non-Gaussian Bayesian tracking, IEEE Transactions on Signal Processing, 50, 2, pp. 174-188, (2002)
  • [6] Choudhury S., Rath S., In-process tool wear estimation in milling using cutting force model, Journal of Materials Processing Technology, 99, 1, pp. 113-119, (2000)
  • [7] Cuppini D., D'Errico G., Rutelli G., Tool wear monitoring based on cutting power measurement, Wear, 139, 2, pp. 303-311, (1990)
  • [8] Danai K., Ulsoy A.G., An adaptive observer for on-line tool wear estimation in turning, part I: Theory, Mechanical Systems and Signal Processing, 1, 2, pp. 211-225, (1987)
  • [9] Danai K., Ulsoy A.G., An adaptive observer for on-line tool wear estimation in turning, part II: Results, Mechanical Systems and Signal Processing, 1, 2, pp. 227-240, (1987)
  • [10] Doucet A., De Freitas N., Gordon N., An Introduction to Sequential Monte Carlo Methods, (2001)
1234