Adhesive performance and fracture toughness evaluation of FRP-reinforced laminated plate

被引：0
作者：
Jung, Hong-Ju [1 ]
Hong, Soon-Il [1 ]
机构：
[1] Department of Forest Biomaterials Engineering, College of Forest and Environmental Sciences, Kangwon National University, Chuncheon
来源：
Journal of the Korean Wood Science and Technology | 2015年 / 43卷 / 06期
关键词：
Adhesive; Fiber reinforced plastic; Fracture toughness; Joints; Soaking delamination; Veneer;
D O I：
10.5658/WOOD.2015.43.6.868
中图分类号：
学科分类号：
摘要：
In order to replace existing slit type steel plate on the wooden structure joint, the FRP-reinforced laminated plates were produced. Four types of FRP-reinforced laminated plates were produced according to the type of reinforcement and adhesive, and before applying to the joint, the adhesion performance test according to KSF 3021 and KSF 2160 and the Compact Tension (CT) type fracture toughness test specified in ASTM D5045-99 were carried out. As a result of adhesion performance test, all GFRP textile, GFRP sheet, and GFRP Textile-Sheet type FRP-reinforced laminated plates satisfied the requirement of soaking delamination percentage with smaller than 5% based on KS standard. However, aramid type specimen satisfied the standard as the soaking delamination percentage of 4.8% but it did not satisfied the standard as the water proof soaking delamination percentage of 70%. As a result of fracture toughness test, the volume ratio of reinforcement to timber became 23% so that the strength of FRP-reinforced laminated plates increased by two to four times in comparison to the control specimen. It was confirmed that the GFRP Textile-Sheet type specimen was most resistant to the fracture most since the ratio of stress intensity factor compared with that of the control increased to 61% owing to the parallel arrangement of glass fiber to the load. As a result of tensile shear strength test using FRP-reinforced laminated plates and nonmetal dowels, it is about 12% lower than metal connectors.
引用
收藏
页码：868 / 875
页数：7
相关论文
共 9 条
  • [1] ASTM D 5045-99, Standard Test Methods for Plane-strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials, (2007)
  • [2] Blass H.J., Schadle P., Ductility aspects of reinforced and non-reinforced timber joints, Engineering Structures, 33, 11, pp. 3018-3026, (2011)
  • [3] Kim K.H., Hong S.I., Bonding performance of glulam reinforced with textile type of glass- and aramid-fiber, GFRP and CFRP, Journal of the Korean Wood Science and Technology, 39, 2, pp. 156-162, (2011)
  • [4] KS F 2160, Determination of Resistance to Soaking Delamination for Adhesive-bonded Wood Products, (2008)
  • [5] KS F 3021, Structural Glued Laminated Timber, (2013)
  • [6] Park J.C., Hong S.I., Strength properties of GFRP reinforced glulam beams bonded with polyvinyl acetate-based emulsion adhesive, Journal of the Korean Wood Science and Technology, 36, 4, pp. 19-25, (2008)
  • [7] Park J.C., Shin Y.J., Hong S.I., Bonding performance of glulam reinforced with glass fiber-reinforced plastics, Journal of the Korean Wood Science and Technology, 37, 4, pp. 357-363, (2009)
  • [8] Raftery G.M., Harte A.M., Rodd P.D., Bond quality at the FRP-wood interface using wood-laminating adhesives, International Journal of Adhesion and Adhesives, 29, 2, pp. 101-110, (2009)
  • [9] Santos C.L., De Jesus A.M., Morais J.J., Fontoura B.F., An experimental comparison of strengthening solutions for dowel-type wood connections, Construction and Building Materials, 46, pp. 114-127, (2013)
1