Study on Microstructure and Properties of 42CrMo Bearing Ring in Cast-rolling Forming and Subsequent Quenching and Tempering

被引：2
|
作者：
Qin F. [1 ]
Qi H. [1 ]
Li Y. [1 ]
Wei X. [1 ]
机构：
[1] Shanxi Key Laboratory of Metallic Materials Forming Theory and Technology, Taiyuan University of Science and Technology, Taiyuan
来源：
Li, Yongtang (liyongtang@tyust.edu.cn) | 1600年 / Chinese Mechanical Engineering Society卷 / 53期
关键词：
42CrMo bearing ring; Cast-rolling forming; Mechanical properties; Microstructure; Quenching and tempering;
D O I：
10.3901/JME.2017.02.026
中图分类号：
学科分类号：
摘要：
The 42CrMo bearing ring is widely used in industry fields, especially as key components in high-speed rail, motor car and wind power, etc. Based on the cast-rolling compound forming of rings, the hot rolling for centrifugal casting 42CrMo bearing, and subsequent quenching and tempering are studied. The microstructure and mechanical properties of the rolled ring are analyzed, and their evolution laws during quenching and tempering are discussed. The results show that the grain is refined through the whole thickness of the rolled ring, while irregular and equiaxed coarse grains are found near the middle-layer and minimum spread. The values of strength and hardness are high, and plasticity and toughness are low. The fracture appearances of both tensile and impact are characterized by dimple mainly gathered in shear lip, which display cleavage fracture. After tempering at 530℃, the carbide does not be found and the plasticity and toughness remain low. A little of fine and dispersed carbide particle is precipitated at 590℃ tempered. Also, the mechanical properties satisfy the standardized demands of production. In these conditions, the tensile fracture has a few of dimples with a large diameter, and the impact fracture is smooth with homogeneous dimple than that at 530℃ tempered. So a good cooperation between strength and plasticity and toughness for the cast-rolling fabricated bearing ring can be obtained in this study. © 2017 Journal of Mechanical Engineering.
引用
收藏
页码：26 / 33
页数：7
相关论文
共 23 条
  • [11] Qin F., Li Y., Deformation behavior at elevated temperature and processing maps of flange blanks on casting-rolling compound forming technology, Journal of Mechanical Engineering, 52, 4, pp. 45-53, (2016)
  • [12] Qin F., Li Y., Micro-texture and mechanical properties of 25Mn large-scale ring based on casting-rolling forming technology, Journal of Mechanical Engineering, 52, 8, pp. 113-118, (2016)
  • [13] Li Y., Qi H., Fu J., Et al., Theoretical and process analyses on the cast-blank rolling forming of 42CrMo bearing rings, Journal of Mechanical Engineering, 49, 6, pp. 198-206, (2013)
  • [14] Qi H.P., Li Y.T., Metadynamic recrystallization of the as-cast 42CrMo steel after normalizing and tempering during hot compression, Chinese Journal of Mechanical Engineering, 25, 5, pp. 853-859, (2012)
  • [15] Guo L., Pan X., Yang H., Et al., Effects of rotational speed of driving roll on microstructure evolution during hot ring rolling of as-cast 42CrMo steel, Heavy Machinery, 3, pp. 59-64, (2012)
  • [16] Hu L., Guo L., Yang H., Et al., Evolution rules of microstructure of as-cast 42CrMo steel blank under different sizes during radial-axial ring rolling process, Journal of Plasticity Engineering, 21, 2, pp. 32-39, (2014)
  • [17] Qin F., Li Y., Qi H., Et al., Research experimental of heat treatment process of 25Mn steel flange based on cast-rolling compound forming technology, Journal of Mechanical Engineering, 50, 14, pp. 95-104, (2014)
  • [18] Chen J., Mo W., Wang P., Et al., Effect of tempering temperature on the impact toughness of steel 42CrMo, Acta Metallurgica Sinica, 48, 10, pp. 1186-1193, (2012)
  • [19] Tian Y., Li Q., Wang Z.D., Et al., Effects of ultra fast cooling on microstructure and mechanical properties of pipeline steels, Journal of Materials Engineering and Performance, 24, pp. 3307-3314, (2015)
  • [20] Qin F.C., Li Y.T., Qi H.P., Et al., Microstructure-texture-mechanical properties in hot rolling of a centrifugal casting ring blank, Journal of Materials Engineering and Performance, 25, pp. 1237-1248, (2016)
123