Titanium Alloy Ti-6Al-4V Prepared by Selective Laser Melting (SLM)

被引：0

作者：

Fousová M. ^{[1
]}

Vojtěch D. ^{[1
]}

Kubásek J. ^{[1
]}

机构：

[1] Department of Metals and Corrosion Engineering, Faculty of Chemical Technology, University of Chemistry and Technology Prague, Prague 6

来源：

Manufacturing Technology | 2016年 / 16卷 / 04期

关键词：

3D printing; mechanical properties; SLM; titanium alloy;

D O I：

10.21062/UJEP/X.2016/A/1213-2489/MT/16/4/691

中图分类号：

学科分类号：

摘要：

Selective laser melting (SLM) as a representant of additive manufacturing technology brings about many advantages into production, which are appreciated especially in the field of biomedical applications and implantology. Our paper is focused on characterization of titanium alloy Ti-6Al-4V (Ti Grade 5) widely used for orthopaedic implants produced by this novel method. Microstructure and mechanical properties are compared with the same material prepared by conventional way of casting, forging and machining. Results show these are almost equivalent. Microstructure is in both cases formed by two phases α+β, but possesses different morphology. Yield strength and ultimate tensile strength of SLM material slightly overpassed values obtained by conventional commercial production (950 MPa and 1000 MPa vs. 877 MPa and 985 MPa). Only elongation was reduced resulting from the presence of some porosity. However, by future optimalization of SLM process parameters, porosity is expected to decrease. Copyright © 2016. Published by Manufacturing Technology. All rights reserved.

引用

页码：14 / 15

页数：1

共 50 条

[31] The Influence of Electron Beam Welding on the Microstructure of Ti-6Al-4V Alloy Produced by Selective Laser Melting Technology [J].

Perevalova, O. B. ;

Panin, A. V. ;

Kazachenok, M. S. ;

Martynov, S. A. .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024,

[32] Anisotropic response of Ti-6Al-4V alloy fabricated by 3D printing selective laser melting [J].

Chen, L. Y. ;

Huang, J. C. ;

Lin, C. H. ;

Pan, C. T. ;

Chen, S. Y. ;

Yang, T. L. ;

Lin, D. Y. ;

Lin, H. K. ;

Jang, J. S. C. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 682 :389-395

[33] Heat treatment of Ti6Al4V alloy fabricated by selective laser melting (SLM) for medical implant: A comprehensive review [J].

Le, Anh Tai ;

Dau, Van Huan ;

Hoang, Tien Dat ;

Nguyen-Xuan, H. .

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2025, 36 :7643-7665

[34] Numerical Study of Laser Cutting of Titanium Alloy (TI-6Al-4V) [J].

Mittal, Vipin ;

Sharma, Pawan ;

Patel, Vijay Kr ;

Pandey, Vikas ;

Kumar, Vinod .

DYNAMICS OF MACHINES AND MECHANISMS, INDUSTRIAL RESEARCH, 2014, 592-594 :579-583

[35] EFFECT OF BORON CARBIDE CONCENTRATION ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF THE Ti-6Al-4V TITANIUM ALLOY PRODUCED BY SELECTIVE LASER MELTING [J].

Filippov, A. A. ;

Golyshev, A. A. .

NANOSCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL, 2020, 11 (04) :283-296

[36] Statistical and optimize of lattice structures with selective laser melting (SLM) of Ti6AL4V material [J].

Kadirgama, K. ;

Harun, W. S. W. ;

Tarlochan, F. ;

Samykano, M. ;

Ramasamy, D. ;

Azir, Mohd Zaidi ;

Mehboob, H. .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 97 (1-4) :495-510

[37] Achieving high strength and ductility in selective laser melting Ti-6Al-4V alloy by laser shock peening [J].

Lv, Jiming ;

Luo, Kaiyu ;

Lu, Haifei ;

Wang, Zhao ;

Liu, Jiajun ;

Lu, Jinzhong .

JOURNAL OF ALLOYS AND COMPOUNDS, 2022, 899

[38] Permanent Mold Casting of Titanium Alloy Ti-6Al-4V [J].

M. Sadayappan ;

M. Sahoo ;

C. Lavender ;

P. Jablonski .

International Journal of Metalcasting, 2008, 2 :69-74

[39] Microstructure homogenizations of Ti-6Al-4V alloy manufactured by hybrid selective laser melting and laser deposition manufacturing [J].

Qin, L. Y. ;

Men, J. H. ;

Zhang, L. S. ;

Zhao, S. ;

Li, C. F. ;

Yang, G. ;

Wang, W. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 759 :404-414

[40] Physical and Hardness Performance at Different Surfaces for Titanium Alloy (Ti6Al4V) Printed Using Selective Laser Melting Process (SLM) [J].

Foudzi, Farhana Mohd ;

Hung, Lai Yu ;

Jamhari, Fathin Iliana ;

Buhairi, Minhalina Ahmad ;

Sulong, Abu Bakar ;

Muhamad, Norhamidi ;

Radzuan, Nabilah Afiqah Mohd ;

Aziz, Izhar ;

Tan, Kim Seah .

JURNAL KEJURUTERAAN, 2024, 36 (03) :1217-1226

← 1 2 3 4 5 →