Effect of oxidant coating boron particle on the ignition and combustion characteristics of boron-based propellant

被引：0
作者：
Chen B.-H. [1 ]
Liu J.-Z. [1 ]
Liang D.-L. [1 ]
Li H.-P. [1 ,2 ]
Zhou J.-H. [1 ]
机构：
[1] State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou
[2] Institute for Energy Studies, Hangzhou Dianzi University, Hangzhou
来源：
Hanneng Cailiao/Chinese Journal of Energetic Materials | 2016年 / 24卷 / 08期
关键词：
Boron-based propellant; Coating; Ignition and combustion characteristics; Oxidant; Thermal oxidation characteristics;
D O I：
10.11943/j.issn.1006-9941.2016.08.009
中图分类号：
学科分类号：
摘要：
The boron-based propellant samples were prepared through coating boron particles with a recrystallization method selecting ammonium perchlorate(AP), ammonium nitrate(AN), nitroguanidine(NQ) and octogen(HMX) as four kinds of oxidants. The effect of different oxidant coating on the ignition and combustion characteristics of boron-based propellant was studied by using TG-DSC and laser ignition test system. The mechanical mixing sample was set as control group. Results show that AP coating can induce low-temperature deflagration of the sample, so as to promote the low-temperature oxidation of boron particles. It helps to effectively shorten the ignition delay time of the sample to 330 ms. By comparing with the mechanical mixing sample, the recrystallization method was found to be the main cause of low-temperature deflagration of the sample. The sample coated by AN has a lower initial reaction temperature of 327.6℃. However, its whole exothermic properties are poor, the average combustion temperature is only 642.8℃. The coating of NQ and HMX can effectively improve the combustion strength of B-based propellants, shorten the combustion time. Among them, NQ can help to improve the maximum combustion intensity. HMX is more conducive to the upgrade of the whole combustion intensity. The coating of HMX makes the combustion time of B-based propellant shorten to 2750 ms, the average combustion temperature reaches 845.5℃ and the heat release is raised to 9968 J·g-1. © 2016, Editorial Board of Chinese Chinese Journal of Energetic Materials. All right reserved.
引用
收藏
页码：774 / 780
页数：6
相关论文
共 23 条
[1]  
Talley C.P., Woods H.P., Combustion of Elemental Boron, (1961)
[2]  
Liang D.-L., Wang Z.-T., Liu J.-Z., Et al., Effect of carbon on the ignition and combustion characteristics of amorphous boron particles, Chinese Journal of Energetic Materials(Hanneng Cailiao), 22, 3, pp. 386-391, (2014)
[3]  
Koch E.C., Klapotke T.M., Boron-based high explosives, Propellants, Explosives, Pyrotechnics, 37, 3, pp. 335-344, (2012)
[4]  
Kuo, Kenneth K., Pein R., Combustion of Boron-Based Solid Propellants and Solid Fuels, pp. 1-81, (1993)
[5]  
Yeh C.L., Kuo K.K., Ignition and combustion of boron particles, Progress in Energy and Combustion Science, 22, 6, pp. 511-541, (1996)
[6]  
Hao L.-F., Zhang L., Tang S.-M., Et al., Technology status and development trends of boron containing fuel-rich propellants, Chemical Propellants & Polymeric Materials, 13, 3, (2015)
[7]  
Liang D., Liu J., Xiao J., Et al., Effect of metal additives on the composition and combustion characteristics of primary combustion products of B-based propellants, Journal of Thermal Analysis and Calorimetry, 122, 1, pp. 497-508, (2015)
[8]  
Xi J., Liu J., Wang Y., Et al., Metal oxides as catalysts for boron oxidation, Journal of Propulsion and Power, 30, 1, pp. 47-53, (2013)
[9]  
Zhang Q.-F., Cao F.-Q., Sun Z.-H., Progress in combustion characteristics of boron-based fuel-rich propellant, Chinese Journal of Energetic Materials(Hanneng Cailiao), 15, 4, pp. 436-440, (2007)
[10]  
Obuchi K., Tanabe M., Kuwahara T., Ignition characteristics of boron particles in the secondary combustor of ducted rockets-effects of magnalium particle addition, 46th AIAA Aerospace Sciences Meeting and Exhibit, pp. 1-8, (2008)
123