Grain Microstructure in Friction-Stir-Welded Dissimilar Al/Mg Joints of Thin Sheets with/without Ultrasonic Vibration

被引:0
作者
Yin, Jialin [1 ]
Liu, Jie [1 ]
Wu, Chuansong [1 ]
机构
[1] Shandong Univ, Inst Mat Joining, MOE Key Lab Liquid Solid Struct Evolut & Mat Proc, Jinan 250061, Peoples R China
关键词
friction-stir welding; Al alloy; Mg alloy; ultrasonic vibration; grain microstructure; dynamic recrystallization; DYNAMIC RECRYSTALLIZATION; MECHANICAL-PROPERTIES; PLASTIC-DEFORMATION; AL-ALLOY; MAGNESIUM; EVOLUTION; SLIP; HOT;
D O I
10.3390/ma17194874
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
Electron backscattered diffraction (EBSD) characterization was conducted on the typical regions in friction-stir-welded dissimilar Al/Mg joints of 2 mm thick sheets with/without ultrasonic assistance. The effects of ultrasonic vibration (UV) on the grain size, recrystallization mechanisms, and degree of recrystallization on both sides of the Al-Mg bonding interface and the intermetallic compounds (IMCs) were investigated. It was found that on the Mg side of the weld nugget zone (WNZ), the primary dynamic recrystallization (DRX) mechanisms were discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX), with geometric dynamic recrystallization (GDRX) playing a secondary role. On the Al side of the WNZ, CDRX was identified as the primary mechanism, with GDRX as a secondary contributor. While UV did not significantly alter the DRX mechanisms in either alloy within the WNZ, it promoted the aggregation and rearrangement of dislocations. This led to an increase in high-angle grain boundaries (HAGBs) and an enhanced degree of recrystallization in the welds. The average grain size in both the Al and Mg alloys of the WNZ followed a pattern of initially increasing and then decreasing along the thickness direction, reaching a maximum in the upper-middle part and a minimum at the bottom. The influence of UV on the average grain size in the WNZ was minimal, with only slight grain refinement observed, and the minimum refinement degree was only 0.9%. The Schmid factor (SF) on the WNZ and thermo-mechanically affected zone (TMAZ) boundary regions of the advancing side (AS) indicates that the application of UV increased the likelihood of basal slip and extension twinning in the crystal structure. In addition, UV reduced the thickness of IMCs and improved the strength of the Al-Mg bonding interface. These results suggest a higher probability of fracture along the TMAZ and WNZ boundary on the AS when UV was applied.
引用
收藏
页数:22
相关论文
共 50 条
  • [41] The Microstructure and Microhardness of Friction Stir Welded Dissimilar Copper/Al-5% Mg Alloys
    Kalashnikova, T. A.
    Shvedov, M. A.
    Vasilyev, P. A.
    PROCEEDINGS OF THE INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS WITH HIERARCHICAL STRUCTURE FOR NEW TECHNOLOGIES AND RELIABLE STRUCTURES 2017 (AMHS'17), 2017, 1909
  • [42] Ultrasonic vibration-induced thinning of intermetallic compound layers in friction stir welding of dissimilar Al/Mg alloys
    Zhao, Junjie
    Wu, ChuanSong
    Su, Hao
    SCIENCE AND TECHNOLOGY OF WELDING AND JOINING, 2022, 27 (08) : 621 - 628
  • [43] Microstructure and Mechanical Properties in Friction Stir Welded Thick Al-Zn-Mg-Cu Alloy Plate
    Qiang, Fei
    Wang, Wen
    Qiao, Ke
    Peng, Pai
    Zhang, Ting
    Guan, Xiao-Hu
    Cai, Jun
    Meng, Qiang
    Zhao, Hua-Xia
    Wang, Kuai-She
    ACTA METALLURGICA SINICA-ENGLISH LETTERS, 2022, 35 (08) : 1329 - 1342
  • [44] Experimental study of the defects, mechanical and microstructural characteristics of friction-stir-welded Al 6061 sheets
    Ahmadi, Mina
    Rahmatabadi, Davood
    Pahlavani, Mostafa
    Marzbanrad, Javad
    Hashemi, Ramin
    Afkar, Amir
    SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2021, 9 (03)
  • [45] Influence of interlayer on microstructure and mechanical properties of friction stir welded dissimilar joints: A review
    Kumar, Mukesh
    Das, Ashish
    Ballav, Raj
    MATERIALS TODAY-PROCEEDINGS, 2020, 26 : 2123 - 2129
  • [46] Microstructure of Ultrasonic-assisted Soldering Mg/Al Dissimilar Metal Joints
    Yu Weiyuan
    Gao Mengzhao
    Zhang Tianyu
    Shang Jiangxu
    Yan Zehua
    RARE METAL MATERIALS AND ENGINEERING, 2018, 47 (10) : 3197 - 3202
  • [47] Effect of Tool Rotational Speeds on the Microstructure and Mechanical Properties of a Dissimilar Friction-Stir-Welded CuCrZr/CuNiCrSi Butt Joint
    Sun, Youqing
    He, Diqiu
    Xue, Fei
    Lai, Ruilin
    METALS, 2018, 8 (07):
  • [48] Microstructure, mechanical and corrosion properties of differently cooled friction stir welded joints of Al and Mg alloys
    Arya, Pradyumn Kumar
    Jain, Neelesh Kumar
    Jayaprakash, Murugesan
    Patel, Vinay Kumar
    SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2022, 10 (03)
  • [49] Microstructure Evolution and Mechanical Properties of High-Speed Friction Stir Welded Aluminum Alloy Thin Plate Joints
    Liu, Fenjun
    Fu, Li
    Chen, Haiyan
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2018, 27 (07) : 3590 - 3599
  • [50] Effect of Material Properties and Process Parameters on Morphology and Strength of Friction-Stir-Welded Dissimilar T-Joints
    N. Manuel
    J. M. Costa
    A. Loureiro
    Journal of Materials Engineering and Performance, 2019, 28 : 5233 - 5244