Multi-pose Motion Synthesis of Three-arm Gear Train Planting Mechanism Based on Genetic Algorithm

被引：0

作者：

Wang L. ^{[1
]}

Sun L. ^{[1
,2
]}

Xu Y. ^{[3
]}

Yu G. ^{[1
,2
]}

Ngambou Lontsi G. ^{[1
]}

Huang J. ^{[1
]}

机构：

[1] Faculty of Mechanical Engineering and Automation, Zhejiang Sci-Tech University, Hangzhou

[2] Key Laboratory of Transplanting Equipment and Technology of Zhejiang Province, Hangzhou

[3] Hangzhou Vocational and Technical College, Hangzhou

来源：

Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery | 2022年 / 53卷 / 06期

关键词：

Genetic algorithm; High-speed transplanter; Motion synthesis; Non-circular gear; Three-arm gear train planting mechanism;

D O I：

10.6041/j.issn.1000-1298.2022.06.007

中图分类号：

学科分类号：

摘要：

In order to further improve the planting efficiency of the high-speed automatic transplanter for vegetable plug seedlings, a three-arm gear train planting mechanism was proposed, and an approximate multi-pose motion synthesis method based on genetic algorithm (GA) was introduced. Firstly, with the key pose (position and orientation) data on the ideal planting trajectory as constraints, the approximate multi-pose motion synthesis optimization model of gear train planting mechanism simplified model (planar RR mechanism) was established by the condition of invariable link length, and the optimal structural parameters of the mechanism were obtained by using Matlab GA toolbox. Then, the total transmission ratio of the gear train was calculated and distributed by the motion parameters of revolute joints of the planar RR mechanism, so as to realize the design of gear train planting mechanism. Finally, the structure design, simulation analysis and test verification of the three-arm gear train planting mechanism were carried out. The results showed that the actual motion trajectory and posture of the mechanism were basically consistent with the theoretical design. When the planting frequency was 120 plants/(min•row) and the theoretical planting spacing was 300 mm, the planting success rate was 96.7%, the actual average planting spacing was 298 mm and the average hole width was 70 mm, which met the requirements of high-speed transplanting. The correctness of the proposed method and practicability of the three-arm gear train planting mechanism were verified. © 2022, Chinese Society of Agricultural Machinery. All right reserved.

引用

页码：70 / 77

页数：7

共 24 条

[1]

YU Xiaoxu, ZHAO Yun, CHEN Baocheng, Et al., Current situation and prospect of transplanter, Transactions of the Chinese Society for Agricultural Machinery, 45, 8, pp. 44-53, (2014)

[2]

HE Yakai, YAN Hua, CUI Wei, Et al., Research situation and analysis on automatic transplanting technology for vegetable seedling, Agricultural Engineering, 8, 3, pp. 1-7, (2018)

[3]

DU S, YU J, WANG W., Determining the minimal mulch film damage caused by the up-film transplanter[J], Advances in Mechanical Engineering, 10, 3, pp. 1-13, (2018)

[4]

ZHOU Fujun, LU Jie, DU Jiaxing, Parameters optimization and experiment of corn-paper transplanting machine with seedling disk, Transactions of the CSAE, 30, 1, pp. 18-24, (2014)

[5]

LI Xuying, WANG Yuwei, LU Guocheng, Et al., Optimization design and test of dibble-type transplanting device, Transactions of the CSAE, 31, 14, pp. 58-64, (2015)

[6]

YU Yingjie, QIN Wei, LAI Qinghui, Et al., Design and experiment of planting mechanism of cauliflower pot seedling transplanter, Transactions of the Chinese Society for Agricultural Machinery, 51, pp. 102-112, (2020)

[7]

LI Pengbin, YAN Hua, WANG Pinlong, Et al., Optimization and test of small plant spacing planting mechanism rod for transplanter, Transactions of the Chinese Society for Agricultural Machinery, 51, pp. 72-78, (2020)

[8]

CHEN Jianneng, WANG Bohong, ZHANG Xiang, Et al., Kinematics modeling and characteristic analysis of multi-linkage transplanting mechanism of pot seeding transplanter with zero speed, Transactions of the CSAE, 27, 9, pp. 7-12, (2011)

[9]

CHEN Xinggu, YIN Wenqing, ZHANG Meina, Optimum design and experiment of crank-rocker and parallelogram linkage mechanism of pot seedling transplanter, Journal of Machine Design, 32, 9, pp. 65-70, (2015)

[10]

YIN Wenqing, LIU Haima, HU Fei, Et al., Optmization design and experiment on eight-linkage planting mechanism of dryland transplanter, Transactions of the Chinese Society for Agricultural Machinery, 51, 10, pp. 51-60, (2020)

← 1 2 3 →