Effects of inlet flow field conditions on the performance of centrifugal compressor diffusers: Part 2-straight-channel diffuser

被引：41

作者：

机构：

[1] Gas Turbine Laboratory, Massachusetts Inst. of Technology, Cambridge

[2] Whittle Laboratory, Department of Engineering, Cambridge University

[3] Praxair, Inc., Technology Center, Tonawanda

来源：

Deniz, S. | 2000年 / ASME, Fairfield卷 / 122期

关键词：

Centrifugation - Flow fields - Recovery - Centrifugal compressors - Aerodynamics - Mach number;

D O I：

10.1115/1.555424

中图分类号：

学科分类号：

摘要：

This is Part 2 of an examination of the influence of inlet flow conditions on the performance and operating range of centrifugal compressor vaned diffusers. The paper describes tests of a straight-channel type diffuser, sometimes called a wedge-vane diffuser, and compares the results with those from the discrete-passage diffusers described in Part 1. Effects of diffuser inlet Mach number, flow angle, blockage, and axial flow nonuniformity on diffuser pressure recovery and operating range are addressed. The straight-channel diffuser investigated has 30 vanes and was designed for the same aerodynamic duty as the discrete-passage diffuser described in Part 1. The ranges of the overall pressure recovery coefficients were 0.50-0.78 for the straight-channel diffuser and 0.50-0.70 for the discrete-passage diffuser, except when the diffuser was choked. In other words, the maximum pressure recovery of the straight-channel diffuser was found to be roughly 10 percent higher than that of the discrete-passage diffuser investigated. The two types of diffuser showed similar behavior regarding the dependence of pressure recovery on diffuser inlet flow angle and the insensitivity of the performance to inlet flow field axial distortion and Mach number. The operating range of the straight-channel diffuser, as for the discrete-passage diffusers, was limited by the onset of rotating stall at a fixed momentum-averaged flow angle into the diffuser, which was for the straight-channel diffuser, α(crit) = 70 ± 0.5 deg. The background, nomenclature, and description of the facility and method are all given in Part 1.

引用

页码：11 / 21

页数：10

共 15 条

[1]

Deniz S., Effects of Inlet Flow Field Conditions on the Performance of Centrifugal Compressor Diffusere, (1997)

[2]

Dong Y., (1996)

[3]

Filipenco V.G., Deniz S., Johnston J.M., Greitzer E.M., Cumpsty N.A., Effects of inlet flow field conditions on the performance of centrifugal compressor diffusers: Part 1 - Discrete-passage diffuser, ASME Journal of Turbomachinery, 122, pp. 1-10, (2000)

[4]

Hunziker R., Einfluss der Diffusorgeometrie auf die Instabilliätsgrenze des Radialverdichters, (1993)

[5]

Japikse D., Osborne C., Optimization of Industrial Centrifugal Compressors

[6]

Part 6B: Studies in Component Performance. - Eight Design Cases From 1972 to 1982, (1986)

[7]

Kano F., Tazawa N., Fukao Y., Aerodynamic performance of large centrifugal compressors, ASME Journal of Engineering for Power, 104, 2, (1982)

[8]

Kenny D.P., A Comparison of the Predicted and Measured Performance of High Pressure Ratio Centrifugal Compressor Diffusers, (1972)

[9]

Krain H., Experimental observation of the flow in impellers and diffusers, Flow in Centrifugal Compressors, (1984)

[10]

Reneau L.R., Johnston J.P., Kline S.J., Performance and design of straight, two-dimensional diffusers, ASME Journal of Basic Engineering, 89, pp. 141-150, (1967)

← 1 2 →