Experimental evaluation of the effect of workpiece heat treatments and cutting parameters on the machinability of Ti-10V-2Fe-3Al β titanium alloy using Taguchi's design of experiments

被引：0

作者：

Khanna N. ^{[1
]}

Rahman Rashid R.A. ^{[2
,3
]}

Palanisamy S. ^{[2
,3
]}

机构：

[1] Mechanical Engineering Department, School of Engineering, IITRAM, Ahmedabad

[2] School of Engineering, Faculty of Science, Engineering and Technology, Swinburne University of Technology, 3122, VIC

[3] Defence Materials Technology Centre, 3122, VIC

来源：

Khanna, Navneet (navneetkhanna@iitram.ac.in) | 1600年 / Inderscience Publishers, 29, route de Pre-Bois, Case Postale 856, CH-1215 Geneva 15, CH-1215, Switzerland卷 / 19期

关键词：

Cutting forces; Cutting temperature; Taguchi design of experiments; Titanium; Turning; Workpiece heat treatment; β;

D O I：

10.1504/IJMMM.2017.086165

中图分类号：

学科分类号：

摘要：

This industry supported scientific investigation presented the steps taken to gain insight into the phenomena of machining β titanium alloy Ti10.2.3 using design of experiments approach. The influence of cutting parameters and workpiece heat treatments on the cutting forces and temperatures during turning of the aerospace grade Ti-10V-2Fe-3Al (Ti.10.2.3) alloy using Taguchi's design of experiments is presented in this work. An L18 orthogonal array was designed and analysis of variance was performed on the tabulated results to investigate the effects of control variables (i.e., cutting speed, feed rate, and workpiece heat treatment) on the output parameters (i.e., cutting force, feed force, and the cutting temperature). The results showed that the feed rate was the most influential factor and the workpiece heat treatment was the least influential parameter which affected the response variables. Based on this observation, optimal cutting parameters and heat treatment conditions were calculated. This work minimised the number of experiments to be carried out to obtain the optimum machining parameters for this specific titanium alloy (Ti.10.2.3). Copyright © 2017 Inderscience Enterprises Ltd.

引用

页码：374 / 393

页数：19

共 27 条

[1]

Arrazola P.J., Garay A., Iriarte L.M., Armendia M., Marya S., Le Maitre F., Machinability of titanium alloys (Ti6Al4V and Ti555.3), Journal of Materials Processing Technology, 209, 5, pp. 2223-2230, (2009)

[2]

Bermingham M., Palanisamy S., Dargusch M., Understanding the tool wear mechanism during thermally assisted machining Ti-6Al-4V, International Journal of Machine Tools and Manufacture, 62, pp. 76-87, (2012)

[3]

Bermingham M., Palanisamy S., Morr D., Andrews R., Dargusch M., Advantages of milling and drilling Ti-6Al-4V components with high-pressure coolant, The International Journal of Advanced Manufacturing Technology, 72, 1-4, pp. 77-88, (2014)

[4]

Bermingham M., Schaffarzyk P., Palanisamy S., Dargusch M., Laser-assisted milling strategies with different cutting tool paths, The International Journal of Advanced Manufacturing Technology, 74, 9-12, pp. 1487-1494, (2014)

[5]

Boyer R.R., Briggs R.D., The use of β titanium alloys in the aerospace industry, Journal of Materials Engineering and Performance, 14, 6, pp. 681-685, (2005)

[6]

Chen Y., Du Z., Xiao S., Xu L., Tian J., Effect of aging heat treatment on microstructure and tensile properties of a new β high strength titanium alloy, Journal of Alloy Compound, 586, pp. 588-592, (2014)

[7]

Dargusch M.S., Zhang M.-X., Palanisamy S., Buddery A., St John D.H., Subsurface deformation after dry machining of Grade 2 Titanium, Advanced Engineering Materials, 10, 1-2, pp. 85-88, (2008)

[8]

Ghosh S., Al-Sabah W.S., Efficient composite designs with small number of runs, Journal of Statistical Planning and Inference, 53, 1, pp. 117-132, (1996)

[9]

Ghosh S., Rao C.R., Design and Analysis of Experiments, (1996)

[10]

Khanna N., Machining metastable β (Ti10.2.3 and Ti5553) titanium alloys: Challenges and solutions, Elevons, 3, 3, pp. 11-14, (2013)

← 1 2 3 →