Supersonic combustion using multiple stinger-shaped injectors

被引：0

作者：

Kouchi T. ^{[1
]}

Tomioka S. ^{[2
]}

Hirano K. ^{[3
,5
]}

Matsuo A. ^{[3
]}

Masuya G. ^{[4
]}

机构：

[1] Department of Mechanical and System Engineering, Okayama University, Okayama

[2] Research and Development Dirct., Japan Aerospace Exploration Agency, Kakuda, Miyagi

[3] Department of Mechanical Engineering, Keio University, Yokohama, Kanagawa

[4] Center for Education and Research on Science for Global Safety, Tohoku University, Sendai, Miyagi

[5] Corporate Technology Division, Kawasaki Heavy Industries, Ltd.

来源：

Kouchi, Toshinori (kouchi@mech.okayama-u.ac.jp) | 2017年 / Japan Society for Aeronautical and Space Sciences卷 / 60期

关键词：

Combustor performance; Fuel mixing; Scramjet engine; Supersonic mixing and combustion;

D O I：

10.2322/tjsass.60.56

中图分类号：

学科分类号：

摘要：

Four stinger injectors arrayed at s/D -6:7 were tested in a Mach 2.44 supersonic combustor with a 1.66° diverging section at T0 = 2060 K. Wall pressure and gas sampling measurements confirmed the ability of the multiple stinger injectors to improve combustor performance. Wall pressure and gas sampling measurements confirmed the ability of the multiple stinger injectors to improve combustor performance. For ψ̎0:3, the combustion region was limited in the diverging section of the combustor, so the combustor was operated in the scramjet mode. For this mode, compared with the airflow between the multiple circular injectors, the airflow much more easily passed between the djacent stinger injectors due to the low blockage effect. As a result, the pressure thrust in the stinger case was 5% higher than that in the circular case. The effects of the injector port shape became unclear when the precombustion shock waves appeared far upstream of the injectors (dual-mode scramjet operation). The fuels from the multiple injectors were uniformly distributed in the span-wise direction, and combustor performance was mainly dominated by the change in airflow momentum flux and disturbance due to the precombustion shock wave.

引用

页码：56 / 59

页数：3

共 15 条

[1]

Gruber M.R., Nejad A.S., Chen T.H., Dutton J.C., Transverse injection from circular and elliptic nozzles into a supersonic crossflow, J. Propul. Power, 16, pp. 449-457, (2000)

[2]

Barber M., Schetz J.A., Roe L.A., Normal, sonic helium injection through a wedge-shaped orifice into supersonic flow, J. Propul. Power, 13, pp. 257-263, (1997)

[3]

Tomioka S., Jacobsen L.S., Schetz J.A., Sonic injection from diamond-shaped orifices into a supersonic crossflow, J. Propul. Power, 19, pp. 104-114, (2003)

[4]

Kobayashi K., Bowersox R., Srinivasan R., Carter C., Hsu K.Y., Flowfield studies of diamond-shaped fuel injector in a supersonic flow, J. Propul. Power, 23, pp. 1168-1176, (2007)

[5]

Srinivasan R., Bowersox R., Simulation of transverse gaseous injection through diamond ports into supersonic freestream, J. Propul. Power, 23, pp. 772-782, (2007)

[6]

Tomioka S., Izumikawa M., Kouchi T., Masuya G., Hirano K., Matsuo A., Matched pressure injections into a supersonic crossflow through diamond-shaped orifices, J. Propul. Power, 24, pp. 471-478, (2008)

[7]

Tomioka S., Kouchi T., Masumoto R., Izumikawa M., Matsuo A., Supersonic combustion with supersonic injection through diamond-shaped orifices, J. Propul. Power, 27, pp. 1196-1203, (2011)

[8]

Hirano K., Matsuo A., Kouchi T., Tomioka S., Izumikawa M., New Injector Geometry for Penetration Enhancement of Perpendicular Jet into Supersonic Flow, (2007)

[9]

Kouchi T., Masuya G., Hirano K., Matsuo A., Tomioka S., Supersonic combustion using a stinger-shaped fuel injector, J. Propul. Power, 29, pp. 639-647, (2013)

[10]

Kouchi T., Hirano K., Kobayashi K., Tomioka S., Izumikawa M., Matsuo A., Combustion Performance of Supersonic Combustor with Stinger-Shaped Fuel Injector, (2008)

← 1 2 →