Asymmetric load and instability characteristics of coal wall at large mining height fully-mechanized face in steeply dipping seam

被引：0
|
作者：
Luo S. [1 ,2 ]
Wu Y. [2 ,3 ]
Liu K. [2 ,3 ,4 ]
Xie P. [2 ,3 ]
Wang H. [2 ,3 ]
机构：
[1] Department of Mechanics, Xi'an University of Science and Technology, Xi'an
[2] Key Laboratory of Western Mine Exploitation and Hazard Prevention Ministry of Education, Xi'an University of Science and Technology, Xi'an
[3] School of Energy Engineering, Xi'an University of Science and Technology, Xi'an
[4] Chongqing Energy (Guizhou) Coal Co., Ltd., Bijie
来源：
Meitan Xuebao/Journal of the China Coal Society | 2018年 / 43卷 / 07期
关键词：
Large mining height; Rib spalling; Steeply dipping seam;
D O I：
10.13225/j.cnki.jccs.2018.0134
中图分类号：
学科分类号：
摘要：
The rib spalling is a technical problem to be solved urgently in steeply dipping thick seam mining.Based on the geological conditions and characteristics of strata behaviors at No.25221 working face in 2130 Coal Mine, the load and instability characteristics of coal wall is investigated by theoretical analysis, numerical simulation, physical analogue material simulation, and field monitoring.Results show that the asymmetry characteristics of mining pressure and strata behavior of large mining height face is higher than that of general mining height face in steeply dipping seam, which is due to mining height increase.Because the inhomogeneous characteristics of the overburden filling are further enhanced, the asymmetric characteristics of the supporting pressure of the coal wall are also obviously increased.During the process of mining, the mechanical properties of coal wall will gradually deteriorate, coal wall crazes and slip body appears.Then the slip body slides along the slip surface, rib spalling emerges, when the surrounding constraints of slip body are relieved or support pressure increases.In inclination direction, the central area is the high incidence area of rib spalling, upper secondary and lower minimum, which is consistent with the asymmetric loading characteristics of coal wall.Besides, in vertical direction, the displacement at the upper part of coal wall is larger than that at the lower part, and rib spalling is easy to occur near the roof area.And under the influence of the gravity tendency component of coal wall, the rib spalling is easy to spread to the upside.On the basis of safety production demands at No.25221 working face in 2130 Coal Mine, some control measures have been proposed in the paper. © 2018, Editorial Office of Journal of China Coal Society. All right reserved.
引用
收藏
页码：1829 / 1836
页数：7
相关论文
共 16 条
  • [1] Wu Y., Liu K., Yun D., Et al., Research progress on the safe and efficient mining technology of steeply dipping seam, Journal of China Coal Society, 39, 8, pp. 1611-1618, (2014)
  • [2] Wu Y., Xie P., Yun D., Et al., Theory and practice of fully mechanized longwall mining in steeply dipping coal seams, Mining Engineering, 65, 1, pp. 35-41, (2013)
  • [3] Wang J., Yu B., Kang H., Et al., Key technologies and equipment for a fully mechanized top-coal caving operation with a large mining height at ultra-thick coal seams, International Journal of Coal Science & Technology, 2, 2, pp. 97-161, (2015)
  • [4] Wang J., Present status and development tendency of fully mechanized coal mining technology and equipment with high cutting height in China, Coal Science and Technology, 34, 1, pp. 4-7, (2006)
  • [5] Yang K., He X., Dou L., Et al., Experimental investigation into stress-relief characteristics with upward large height and upward mining under hard thick roof, International Journal of Coal Science & Technology, 2, 1, pp. 91-96, (2015)
  • [6] Han H., Wang Z., Guo B., Coal wall spalling mechanism and prevention technology of unstable seam with soft roof, soft coal and soft floor, Coal Science and Technology, 44, 4, pp. 34-38, (2016)
  • [7] Huang Q., Liu J., Vertical slice model for coal wall spalling of large mining height longwall face in shallow seam, Journal of Mining & Safety Engineering, 32, 2, pp. 187-191, (2015)
  • [8] Zhao Y., Zhang X., Tu M., Roof caving characteristic and strata behavior in exploiting steep coal seams, Journal of Mining & Safety Engineering, 24, 2, pp. 231-234, (2007)
  • [9] Yin G., Xian X., Dai G., Et al., Basic behaviors of strata movement in seam with deep dip angle, Chinese Journal of Geotechnical Engineering, 23, 4, pp. 450-453, (2001)
  • [10] Meng X., Wen R., Liu J., Et al., Research on sitemeasurement of ground behavior in fullymechan ized caving m ining face in high inclined seam of 1000 m deep mine, Coal Science and Technology, 35, 11, pp. 14-17, (2007)
12