Tribology in tool / material interface during forming

被引：0
作者：
Makino, Takehiko [1 ]
机构：
[1] Department of Electrical and Mechanical Engineering, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya-shi, Aichi,466-8555, Japan
来源：
Toraibarojisuto/Journal of Japanese Society of Tribologists | 2018年 / 63卷 / 07期
关键词：
Tribology; -; Friction;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
In micro/meso (between macro and micro)-scale metal forming, the contribution of friction between the tool and material on the material deformation is higher than that in macro-scale metal forming. The friction between tool and material in this scale is essentially nonuniform and nonconstant during forming. The interfacial phenomena including the friction force and adhesion were studied by the following method: direct measurement of friction force during forming, the atomistic calculation of ceramics/aluminum interface during forming, and the contact potential difference (CPD) measurement of tool surface after forming. The CPD measured on the tool surface can be compared with the electronic state calculated on adhered surface. © 2018 Japanese Society of Tribologists. All rights reserved.
引用
收藏
页码：459 / 465
相关论文
共 50 条
[41]   EFFECT OF TOOL MATERIAL AND PROCESS PARAMETERS ON SURFACE CONDITIONS IN SINGLE POINT INCREMENTAL FORMING (SPIF) OF POLYMERIC MATERIALS [J].
Ragai, Ihab ;
Goldstein, Joe ;
Meyer, Cayla ;
Upcraft, Clayton .
PROCEEDINGS OF ASME 2022 INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, IMECE2022, VOL 2A, 2022,
[42]   The tribology between monocrystalline diamond and polycrystalline cubic boron nitride during frictional contact [J].
Mueller, Ulrich ;
Kaiser, Josef ;
Barth, Sebastian ;
Bergs, Thomas .
JOURNAL OF MANUFACTURING PROCESSES, 2021, 68 :1147-1157
[43]   Analysis of Tool Geometry and Lubrication Conditions Effect on the Forming Load During Wire Drawing Process [J].
Shukur, Jalil J. ;
Khudhir, Waqass S. ;
Abbood, Mohanad Qusay .
ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL, 2022, 16 (04) :279-286
[44]   Tribological issues during quick plastic forming [J].
Paul E. Krajewski ;
Arianna T. Morales .
Journal of Materials Engineering and Performance, 2004, 13 :700-709
[45]   Tribological issues during quick plastic forming [J].
Krajewski, PE ;
Morales, AT .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2004, 13 (06) :700-709
[46]   Experimental investigation of the effect of disk acceleration and velocity on the tribology of the head/disk interface [J].
Zhao, Q ;
Talke, FE ;
Meeks, SW .
IEEE TRANSACTIONS ON MAGNETICS, 1999, 35 (05) :2406-2408
[47]   Tribology applications of surface reflectance analyzers: optical characterization of the head disk interface [J].
Vurens, GH ;
Klein, DL ;
Gan, W ;
Ultican, T .
TRIBOLOGY INTERNATIONAL, 2000, 33 (09) :647-653
[48]   Special Issue on Who's Who in Tribology 2009 Mechanical & Material Engineering Division, Kanagawa Industrial Technology Center [J].
Kano, M. ;
Horiuchi, T. ;
Yoshida, K. .
JOURNAL OF JAPANESE SOCIETY OF TRIBOLOGISTS, 2010, 55 (03) :182-182
[49]   Improved tool wear properties in sheet metal forming using Carbide Steel, a novel abrasion resistant cast material [J].
Nilsson, A. ;
Kirkhorn, L. ;
Andersson, M. ;
Stahl, J. -E. .
WEAR, 2011, 271 (9-10) :1280-1287
[50]   Exploring tribology and material contact science in spine surgery: implications for implant design [J].
Scariano, Gabrielle ;
Meade, Seth ;
Sultan, Assem ;
Shost, Michael ;
Benzel, Edward ;
Krishnaney, Ajit ;
Mroz, Thomas ;
Steinmetz, Michael ;
Habboub, Ghaith .
JOURNAL OF NEUROSURGERY-SPINE, 2024, 40 (06) :801-810
12345