Numerical Study on Turbulent Forced Convection and Heat Transfer Characteristic in a Circular Tube with V-Orifice

被引：3

作者：

Jedsadaratanachai W. ^{[1
]}

Boonloi A. ^{[2
]}

机构：

[1] Department of Mechanical Engineering, Faculty of Engineering, King Mongkut's Institute of Technology Ladkrabang, Bangkok

[2] Department of Mechanical Engineering Technology, College of Industrial Technology, King Mongkut's University of Technology North Bangkok, Bangkok

来源：

Modelling and Simulation in Engineering | 2017年 / 2017卷

关键词：

Finite volume method - Heat exchangers - Reynolds number - Heat transfer;

D O I：

10.1155/2017/3816739

中图分类号：

学科分类号：

摘要：

Performance assessments on heat transfer, pressure loss, and thermal enhancement factor in the circular tube heat exchanger inserted with the V-orifices are investigated numerically. The influences of the blockage ratio, gap spacing ratio, and orifice arrangement are reported for turbulent regime, Re=3000-10,000. The finite volume method and SIMPLE algorithm are selected to solve the present problem. The mechanisms on flow and heat transfer characteristics are described. The periodic concepts on flow and heat transfer are also studied. The numerical results show that the gap spacing ratio is main reason for the changes of the flow and heat transfer topologies. The gap distance helps to adjust the optimum point of the thermal performance, especially at high flow blockage ratio. In addition, the optimum thermal performance of the present system is around 2.25 at the lowest Reynolds number, Re=3000. © 2017 Withada Jedsadaratanachai and Amnart Boonloi.

引用

共 33 条

[1]

Kongkaitpaiboon V., Nanan K., Eiamsa-Ard S., Experimental investigation of convective heat transfer and pressure loss in a round tube fitted with circular-ring turbulators, International Communications in Heat and Mass Transfer, 37, pp. 568-574, (2010)

[2]

Yakut K., Sahin B., Flow-induced vibration analysis of conical-rings used of heat transfer enhancement in heat exchanger, Applied Energy, 78, pp. 273-288, (2004)

[3]

Yakut K., Sahin B., Canbazoglu S., Performance and flowinduced vibration characteristics for conical-ring turbulators, Applied Energy, 79, pp. 65-76, (2004)

[4]

Durmus A., Heat transfer and exergy loss in cut out conical turbulators, Energy Conversion and Management, 45, pp. 785-796, (2004)

[5]

Eiamsa-Ard S., Promvonge P., Experimental investigation of heat transfer and friction characteristics in a circular tube fittedwithV-nozzle turbulators, International Communications in Heat and Mass Transfer, 33, pp. 591-600, (2006)

[6]

Eiamsa-Ard S., Promvonge P., Effect of V-nozzle inserts and snail with free spacing entry on heat transfer in a heat exchanger, Journal of Energy Heat and Mass Transfer, 28, pp. 225-239, (2006)

[7]

Promvonge P., Eiamsa-Ard S., Heat transfer augmentation in a circular tube using V-nozzle turbulator inserts and snail entry, ExperimentalThermal and Fluid Science, 32, pp. 332-340, (2007)

[8]

Promvonge P., Eiamsa-Ard S., Heat transfer and turbulent flow friction in a circular tube fitted with conical-nozzle turbulators, International Communications in Heat and Mass Transfer, 34, 1, pp. 72-82, (2007)

[9]

Promvonge P., Eiamsa-Ard S., Heat transfer in a circular tube fitted with free-spacing snail entry and conical-nozzle turbulators, International Communications in Heat and Mass Transfer, 34, 7, pp. 838-848, (2007)

[10]

Promvonge P., Eiamsa-Ard S., Heat transfer behaviors in a tube with combined conical-ring and twisted-tape insert, International Communications in Heat and Mass Transfer, 34, 7, pp. 849-859, (2007)

← 1 2 3 4 →