Fabrication and test of high-precision off-axis aspheric lens

被引：0
|
作者：
Zhong B. [1 ,2 ]
Chen X. [1 ]
Wang J. [1 ]
Zhou L. [1 ]
Shi Q. [1 ]
Deng W. [1 ]
机构：
[1] Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang
[2] School of Mechanical and Electrical Engineering, University of Electronic Science and Technology of China, Chengdu
来源：
Hongwai yu Jiguang Gongcheng/Infrared and Laser Engineering | 2018年 / 47卷 / 07期
关键词：
Advanced optical manufacturing; Bonnet polishing; Full frequency error; Pitch polishing;
D O I：
10.3788/IRLA201847.0718003
中图分类号：
学科分类号：
摘要：
In order to meet the requirement of high precision and mass manufacturing of large aspheric lens for high power laser device, a novel manufacturing method combining the bonnet polishing (BP) technology and flexible pitch polishing (FPP) technology was explored. Firstly, after the aspheric generating by ultra-precision grinding, the bonnet polishing technology, in keeping the aspherical surface shape, was used to quickly remove the grinding defect layer and improve the roughness of the element so that it can be directly tested by interferometer. Then, the bonnet polishing technology was used to quickly correct the low frequency error. Finally, the flexible pitch tool was adopted to smooth the middle and high frequency error. During the polishing process, the self-built wavefront detection system and the roughness instrument were used to detect the full frequency error of the aspheric element. Based on the above-mentioned fabrication and testing method, a 430 mm ×430 mm off-axis apherical lens was manufactured, and the results indicate that, after polishing, the PV, GRMS, PSD1 RMS, PSD2 RMS and Rq are 0.1λ, 5.7 nm/cm, 1.76 nm, 1 nm and 0.6 nm, respectively. In addition, the power spectral density (PSD) curves are below the required evaluation curve. The experimental results show that the full frequency specifications of the off-axis aspheric lens meet the requirements. The manufacturing method is also applicable to the high-precision manufacturing of other types of large aspheric optical elements. © 2018, Editorial Board of Journal of Infrared and Laser Engineering. All right reserved.
引用
收藏
相关论文
共 15 条
  • [1] Spaeth M.L., Manes K.R., Widmayer C.C., Et al., The national ignition facility wavefront requirements and optical architecture, Optical Engineering, 43, 12, pp. 25-42, (2004)
  • [2] Semenov A.P., Abdulkadyrov M.A., Belousov S.P., Et al., Technological features of the fabrication of the primary mirrors of telescopes, J Opt Technol, 80, 4, pp. 207-213, (2013)
  • [3] Martin H.M., Allen R.G., Burge J.H., Et al., Fabrication and testing of the first 8. 4 m off-axis segment for the Giant Magellan Telescope, SPIE, 7739, (2010)
  • [4] Yu G.Y., Walker D.D., Li H.Y., Research on fabrication of mirror segments for E-ELT, SPIE, 8416, (2012)
  • [5] Glatzel H., Ashworth D., Bremer M., Et al., Projection optics for extreme ultraviolet lithography (EUVL) micro-field exposure tools (METs) with a numerical aperture of 0.5, SPIE Advanced Lithography, 8679, 1, (2013)
  • [6] Meng X., Wang Y., Ma X., Et al., Fabrication and test for 520 mm secondary mirror of on-axis three mirror space camera, Infrared and Laser Engineering, 46, 8, (2017)
  • [7] Zhang X., Luo X., Yan L., Et al., Technology of large aperture off-axis parabolic mirror with Tri-station processing center, Infrared and Laser Engineering, 45, 8, (2016)
  • [8] Aikens D.M., The origin and evolution of the optics for the national ignition facility, SPIE, 2536, pp. 2-12, (1995)
  • [9] Campbell J.H., Hawley-Fedder R., Stolz C.J., NIF optical materials and fabrication technologies: an overview, SPIE, 5341, (2004)
  • [10] Pan J.H., Design, Fabrication and Test of Optical Aspheric Surface, (2004)
12