Microstructure and mechanical properties of 30SiMnCrB5 hot stamping steel

被引：0

作者：

Cheng, Jun-Ye ^{[1
]}

Chen, Yin-Li ^{[1
]}

Zhao, Ai-Min ^{[1
]}

Ding, Ran ^{[1
]}

Wang, Ze-Han ^{[1
]}

Kuang, Shuang ^{[2
]}

Jiang, Ying-Hua ^{[2
]}

机构：

[1] Metallurgical and Ecological Engineering Research Institute, University of Science and Technology Beijing, Beijing

[2] Shougang Research Institute of Technology, Shougang Group Corporation, Beijing

来源：

Beijing Keji Daxue Xuebao/Journal of University of Science and Technology Beijing | 2014年 / 36卷 / 10期

关键词：

Alloy steel; Hot stamping; Mechanical properties; Microstructure; Orientation;

D O I：

10.13374/j.issn1001-053x.2014.10.004

中图分类号：

学科分类号：

摘要：

A C-Si-Mn-Cr-B hot stamping steel was designed to improve its comprehensive properties. The continuous cooling transformation (CCT) curves and phase transformation rules of 30SiMnCrB5 hot stamping steel were measured and studied by thermal dilatometry. The microstructure morphology and mechanical properties of 30SiMnCrB5 steel sheet after rolling, annealing and hot stamping simulated were analyzed by scanning electron microscopy, transmission electron microscopy and tensile testing. The orientation relationship between martensite variants and parent phases in the hot-stamped steel sheet was determined by pole figure contouring. It is found that the critical cooling rate of 30SiMnCrB5 hot stamping steel is 5 ℃ ·s-1 with good hardenability which inhibits the formation of pearlite and bainite effectively. The hardness of full martensite is more than 600 HV. The microstructure of the hot-stamped steel sheet is composed of lath martensite and retained austenite, which accounts for 6% to 8% and distributes between martensite laths by film. The strength and ductility of the hot-stamped steel sheet are matched well with a tensile strength of about 1800 MPa and a total elongation up to 10%. The orientation relationship between martensite variants and parent phases in the hot-stamped steel sheet is closer to the N-W orientation relationship, which the 12 variants do not appear wholly in prior austenite.

引用

页码：1299 / 1306

页数：7

共 18 条

[1] Karbasianm H., Tekkaya A.E., A review on hot stamping, J Mater Process Technol, 210, 15, (2010)
[2] Dong W.F., Kim H.S., De Cooman B.C., A review of the physical metallurgy related to the hot press forming of advanced high strength steel, Steel Res Int, 80, 3, (2009)
[3] Li H.P., Zhao G.Q., Zhang L., Et al., The development status of hot stamping and quenching of ultra high-strength steel, J Shandong Univ Eng Sci, 40, 3, (2010)
[4] Li H.P., Zhao G.Q., He L.F., Et al., Research on the constitutive relationship of hot stamping boron steel B1500HS at high temperature, J Mech Eng, 48, 8, (2012)
[5] Ma N., Zhang Z.H., Hu P., Et al., Microstructure and mechanical behavior of new type multi-layer metallic composite material in hot forming, J Mater Eng, 5, (2011)
[6] Naderi M., Saeed-Akbari A., Bleck W., The effects of non-isothermal deformation on martensitic transformation in 22MnB5 steel, Mater Sci Eng A, 487, 1-2, (2008)
[7] Naderi M., Ketabchi M., Abbasi M., Et al., Analysis of microstructure and mechanical properties of different high strength carbon steels after hot stamping, J Mater Process Technol, 211, 6, (2011)
[8] Nikravesh M., Naderi M., Akbari G.H., Influence of hot plastic deformation and cooling rate on martensite and bainite start temperatures in 22MnB5 steel, Mater Sci Eng A, 540, (2012)
[9] So H., Fabetamann D., Hoffmann H., Et al., An investigation of the blanking process of the quenchable boron alloyed steel 22MnB5 before and after hot stamping process, J Mater Process Technol, 212, 2, (2012)
[10] Jang J.H., Lee J., Joo B., Et al., Flow characteristics of aluminum coated boron steel in hot press forming, Trans Nonferrous Met Soc China, 19, 4, (2009)

← 1 2 →