Influence of Ti on Grain Growth Behavior of Non-quenched and Tempered Plastic Mold Steel

被引：0
|
作者：
Zheng Y. [1 ,2 ,3 ]
Li X. [1 ,2 ,3 ]
Wu R. [1 ,2 ,3 ]
Wu X. [1 ,2 ,3 ]
机构：
[1] State Key Laboratory of Advanced Special Steel, Shanghai University, Shanghai
[2] Shanghai Key Laboratory of Advanced Ferrometallurgy, Shanghai University, Shanghai
[3] School of Materials Science and Engineering, Shanghai University, Shanghai
来源：
Wu, Xiaochun (wuxiaochun@t.shu.edu.cn) | 1600年 / Cailiao Daobaoshe/ Materials Review卷 / 31期
关键词：
Austenization; Micro-alloying; Non-quenched and tempered steel; Precipitation;
D O I：
10.11896/j.issn.1005-023X.2017.08.017
中图分类号：
学科分类号：
摘要：
The demand of automotive and appliance industry for high-quality large section plastic mold steel is gradually increased. However, with the increase of the thickness of plastic mold steel, the possibility of the occurrence of coarse grain is also increased, which calls for a reasonable design of heat treatment process. The austenite grain growth behavior during high temperature treatment was hindered by adding titanium, and the effects of Ti addition on austenite grain growth behavior of non-quenched and tempered (NQT) plastic mold steel were emphatically studied. The results show that the NQT plastic mold steel containing 0.03% Ti has better resistance to grain coarsening when the homogenization temperature is higher than 1 050℃, due to the Ti(C, N) precipitation disperse around the grain boundaries. Based on the experimental results, the mathematical models of grain growth were established, which can be used to predict the austenite grain growth of NQT plastic mold steel during high temperature homogenization. © 2017, Materials Review Magazine. All right reserved.
引用
收藏
页码：82 / 87and108
相关论文
共 26 条
  • [1] Duan L.L., Zhang Z., Li X.C., Et al., Transformation process and kinetics in a new plastic mould of bainite steel SDP2, Trans Mater Heat Treatment, 36, 8, (2015)
  • [2] Wu R.M., Zheng Y.F., Wu X.C., Et al., Effect of titanium on the microstructure and hardness uniformity of non-quenched and tempered pre-hardened steel for large-section plastic mould, Ironmaking Steelmaking, 44, 1, (2017)
  • [3] Zhang Z., Wu X.C., Zhou Q., Et al., Effect of microstructure on the impact toughness of a bainitic steel bloom for large plastic molds, Int J Mine Metal Mater, 22, 8, (2015)
  • [4] Wu X.C., Cui K., Effect of V, Ti on the microstructures and mecha-nical properties of unquenched and un-tempered die steel for plastic mold, Mater Mech Eng, 21, 6, (1997)
  • [5] Wu X.C., Cui K., Preciptated phase in unquenched and un-tempered die steel for plastic mould, Iron Steel, 33, 6, (1998)
  • [6] Luo Y., Wu X.C., Wang H.B., Et al., Study on microstructure and hardness uniformity of non-quenched prehardened steel for large section plastic mould, Mater Sci Eng A, 492, (2008)
  • [7] Luo Y., Wu X.C., Wang H.B., Et al., A comparative study on non-quenched and quenched prehardened steel for large section plastic mould, J Mater Process Technol, 209, (2009)
  • [8] Luo Y., Peng J.M., Wang H.B., Et al., Effect of tempering on microstructure and mechanical properties of a non-quenched bainitic steel, Mater Sci Eng A, 527, (2010)
  • [9] Zhang Z., Wu X.C., Li N., Et al., Alloy optimisation of bainitic steel for large plastic mould, Mater Sci Technol, 31, 14, (2015)
  • [10] Ma H., Liao S.L., Effect of Ti on austenite grain growth behavior in high carbon steels, J Iron Steel Res Int, 21, 7, (2014)
123