Influence of surface topography deformation on friction atsliding contact interface in metal forming

被引：0
作者：
Hu, Zhao-Wen [1 ]
Liu, Kun [1 ]
Liu, Xiao-Jun [1 ]
Liu, Kui [1 ]
机构：
[1] School of Mechanical and Automotive Engineering, Hefei University of Technology, Hefei
来源：
Mocaxue Xuebao/Tribology | 2015年 / 35卷 / 04期
基金：
中国国家自然科学基金;
关键词：
Contact interface; Friction; Surface texturing; Surface topography;
D O I：
10.16078/j.tribology.2015.04.003
中图分类号：
学科分类号：
摘要：
In order to obtain a better understanding of the frictional behavior at sliding contact interface in metal forming, a novel friction test apparatus was built up. A series of strip drawing friction tests using aluminum 1050 sheet specimens with two types of texturing topographies were conducted at different contact pressures and sliding speeds. The three dimensional surface topographies of specimens before and after tests were measured. Such three dimensional surface parameters as real contact area ratio, closed void area ratio and open void area ratio, were used to describe the variations of surface topography of specimens. Experimental results show that the friction coefficient decreases with increasing nominal contact pressure and sliding speed. The initial surface topography of the specimens has a definite influence on the friction behavior. The three dimensional surface topographies and parameters of the specimens vary regularly with contact conditions. Based on mechani-cal-rheological model, it is found that depending on the surface topography deformation, different mechanisms determine the friction behavior. The dependence of the friction coefficient on nominal contact pressure and sliding speed can be attributed to micro-plasto-hydrodynamic lubrication and hydrodynamic entrainment in the inlet at the interface respectively. ©, 2015, Science Press. All right reserved.
引用
收藏
页码：368 / 377
页数：9
相关论文
共 15 条
  • [1] Tisza M., A general overview of tribology of sheet metal forming, Journal for Technology of Plasticity, 26, 2, pp. 11-25, (2001)
  • [2] Wang Z.G., Ultra-smooth surface finishing by metal forming processes, Forging & Stamping Technology, 2, pp. 1-4, (2003)
  • [3] Lo S.-W., Horng T.-C., Surface roughening and contact behavior in forming of aluminum sheet, ASME J Tribol, 121, 2, pp. 224-233, (1999)
  • [4] Zhao Z.D., Wang J.A., Wang L.J., Research on the relationship between average friction coefficient and contact press in metal forming, China Metal Forming Equipment & Manufacturing Technology, 1, pp. 40-43, (2006)
  • [5] Masters I.G., Williams D.K., Roy R., Friction behavior in strip draw test of pre-stretched high strength automotive aluminum alloys, International Journal of Machine Tools and Manufacture, 73, pp. 17-24, (2013)
  • [6] Payen G.R., Felder E., Repoux M., Et al., Influence of contact pressure and boundary films on the frictional behavior and on the roughness changes of galvanized steel sheets, Wear, 276-277, pp. 48-52, (2012)
  • [7] Ahmed R., Sutcliffe M.P.F., An experimental investigation of surface pit evolution during cold-rolling or drawing of stainless steel strip, Journal of Tribology, 123, 1, pp. 1-7, (2001)
  • [8] Bech J., Bay N., Eriksen M., Entrapment and escape of liquid lubricant in metal forming, Wear, 232, 2, pp. 134-139, (1999)
  • [9] Zhou R., Cao J., Wang Q.J., Et al., Effect of EDT surface texturing on tribological behavior of aluminum sheet, Journal of Materials Processing Technology, 211, 10, pp. 1643-1649, (2011)
  • [10] Liu X.J., Liewald M., Becker D., Effects of rolling direction and lubricant on friction in sheet metal forming, Journal of tribology, 131, 4, pp. 1-7, (2009)
12