Mimimizing the cost of using tractors at agricultural operations

被引:0
作者
Zaynagabdinov R. [1 ]
Gabitov I. [1 ]
Bakiev I. [1 ]
Gafurov I. [1 ]
Kostarev K. [1 ]
机构
[1] Department Automobiles and Machine-Tractor Complexes, Federal State Budgetary Educational Establishment of Higher Education “Bashkir State Agrarian University”, Ufa
来源
Diagnostyka | 2020年 / 21卷 / 02期
关键词
Crop production; DT-75; tractor; Integer programming; Optimal planning; T-402;
D O I
10.29354/diag/122340
中图分类号
学科分类号
摘要
The paper shows the economic efficiency of the optimal use of technology in crop production. A totally new model has been developed,that allows planning the operation of each tractor individually, as well as an integer programming method with Boolean variables based on the formation of a lexicographic sequence. The paper shows the calculation according to the optimization criterion of the minimum duration of the work. The developed method of integer programming is original because it allows to solve problems typical of agricultural planning. For this, the authors derived a formula for the formation of any member of the lexicographic sequence and developed the AgroMaster + computer program, which also carries out the search for the optimal solution using the method of truncated exhaustive search. Due to optimal planning, the total duration of agricultural operations is reduced by 1.7 times compared to their actual duration. The cost of additional products received per 1 moto-hour is 7.3 dollars. The testing the results of studies in one of the farms of the Republic of Bashkortostan showed the possibility of practical application of the above developments for optimal planning of tractors in any agricultural enterprises. © 2020 Polish Society of Technical Diagnostics. All rights reserved.
引用
收藏
页码:41 / 49
页数:8
相关论文
共 50 条
[41]   An Extended Kalman Filter for Low-Cost Positioning System in Agricultural Vehicles [J].
Kumar, Nenavath Ravi ;
Nagabhooshanam, E. .
PROCEEDINGS OF THE 2016 IEEE INTERNATIONAL CONFERENCE ON WIRELESS COMMUNICATIONS, SIGNAL PROCESSING AND NETWORKING (WISPNET), 2016, :151-157
[42]   Ergonomic assessment of drivers in MF285 and MF399 tractors during clutching using algometer [J].
Fallahi H. ;
Abbaspour-Fard M.H. ;
Azhari A. ;
Khojastehpour M. ;
Nikkhah A. .
Information Processing in Agriculture, 2016, 3 (01) :54-60
[43]   Development of the Reliability Assessment Process of the Hydraulic Pump for a 78 kW Tractor during Major Agricultural Operations [J].
Siddique, Md Abu Ayub ;
Kim, Yong-Joo ;
Baek, Seung-Min ;
Baek, Seung-Yun ;
Han, Tae-Ho ;
Kim, Wan-Soo ;
Kim, Yeon-Soo ;
Lim, Ryu-Gap ;
Choi, Yong .
AGRICULTURE-BASEL, 2022, 12 (10)
[44]   Intelligent Surface Recognition for Autonomous Tractors Using Ensemble Learning with BNO055 IMU Sensor Data [J].
Thavitchasri, Phummarin ;
Maneetham, Dechrit ;
Crisnapati, Padma Nyoman .
AGRICULTURE-BASEL, 2024, 14 (09)
[45]   PERFORMANCE OF AN AGRICULTURAL DIESEL ENGINE USING DIFFERENTS FUELS [J].
Perin, Gismael F. ;
Schlosser, Jose F. ;
Galon, Leandro ;
Rodrigues, Fabricio A. ;
Frantz, Ulisses G. .
ENGENHARIA AGRICOLA, 2017, 37 (01) :91-97
[46]   Forest Operations Using a Combi-Forwarder in Deciduous Forests [J].
Stoilov, Stanimir ;
Proto, Andrea Rosario ;
Oslekov, Delyan ;
Angelov, Georgi ;
Papandrea, Salvatore Francesco .
SMALL-SCALE FORESTRY, 2024, 23 (01) :25-40
[47]   Efficient Utilization of Employees in the Garment Industry Using Operations Research [J].
Fernando, W. K. I. ;
Suriyaarachchi, D. J. C. .
2008 4TH INTERNATIONAL CONFERENCE ON INFORMATION AND AUTOMATION FOR SUSTAINABILITY (ICIAFS), 2008, :40-+
[48]   Environmental Impact Assessment of Agricultural Production Using LCA: A Review [J].
Alhashim, Rahmah ;
Deepa, Raveendranpillai ;
Anandhi, Aavudai .
CLIMATE, 2021, 9 (11)
[49]   Autonomous Agricultural Sprayer using Machine Vision and Nozzle Control [J].
Terra, Fabio P. ;
do Nascimento, Gustavo H. ;
Duarte, Gabrielle A. ;
Drews-Jr, Paulo L. J. .
JOURNAL OF INTELLIGENT & ROBOTIC SYSTEMS, 2021, 102 (02)
[50]   A PRELIMINARY STUDY OF ACTIVE STABILIZATION FOR AGRICULTURAL MACHINES USING A MOVABLE MASS [J].
Bietresato, Marco ;
Belotti, Roberto ;
von Ellenrieder, Karl D. ;
Mazzetto, Fabrizio .
PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2019, VOL 4, 2020,