Effect of inter layer idle time on thermal behavior for multi-layer single-pass thin-walled parts in GMAW-based additive manufacturing

被引:0
|
作者
机构
[1] Lei, Yangyang
[2] Xiong, Jun
[3] Li, Rong
来源
Xiong, Jun (xiongjun@home.swjtu.edu.cn) | 1600年 / Springer London卷 / 96期
关键词
D O I
暂无
中图分类号
学科分类号
摘要
Components fabricated in gas metal arc welding (GMAW)-based additive manufacturing undergo a special thermal process with many reheating cycles, resulting in the complicated thermal behavior. Many process variables can affect the thermal history in GMAW-based additive manufacturing, especially the interlayer idle time. In this paper, three-dimensional transient models were established to research the effect of interlayer idle time on thermal process in GMAW-based additive manufacturing. Meanwhile, a confirmatory test was conducted to verify the effectiveness of the model. The results indicate that the total maximum temperature gradients of the molten pool at the middle points in the models with the interlayer idle time of 2 min, 5 min, and cooling to room temperature are approximately consistent after the fourth layer, and those in the case with continuous deposition decrease gradually. As the deposition height increases, the maximum temperature gradient in molten pool along the deposition path keeps steady in the model with cooling to room temperature. At the deposition ending moment, with the increasing interlayer idle time, the total temperature gradients at the middle points of the layers decrease in the first eight layers and increase in the ninth and tenth layers, while the circumferential temperature gradients increase progressively. © 2018, Springer-Verlag London Ltd., part of Springer Nature.
引用
收藏
页码:1 / 4
相关论文
共 41 条
  • [21] Scanning Strategy of Multi-Layer and Multi-Track Laser Cladding for Radial Grooves of Annular Thin-walled Parts
    Wang, Lei
    Wu, Xianwang
    Wang, Tong
    Zhang, Zelin
    Jin, Xianzhi
    Xia, Xuhui
    Liu, Yubo
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2025, 34 (01) : 397 - 418
  • [22] Vision-sensing and bead width control of a single-bead multi-layer part: material and energy savings in GMAW-based rapid manufacturing
    Xiong, Jun
    Zhang, Guangjun
    Qiu, Zhilong
    Li, Yongzhe
    JOURNAL OF CLEANER PRODUCTION, 2013, 41 : 82 - 88
  • [23] The Influence of Magnetic Arc Oscillation on the Deposition Width Variation along the Length of Multi-layer Single-Pass Walls Produced by Wire Arc Additive Manufacturing Process
    Corradi, Diego Raimundi
    Coelho, Fagner Guilherme
    Antonello, Miguel Guilherme
    Bracarense, Alexandre Queiroz
    Arias, Ariel Rodriguez
    Barbosa, Tarsis Prado
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2021, 30 (07) : 5278 - 5289
  • [24] The Influence of Magnetic Arc Oscillation on the Deposition Width Variation along the Length of Multi-layer Single-Pass Walls Produced by Wire Arc Additive Manufacturing Process
    Diego Raimundi Corradi
    Fagner Guilherme Coelho
    Miguel Guilherme Antonello
    Alexandre Queiroz Bracarense
    Ariel Rodriguez Arias
    Tarsis Prado Barbosa
    Journal of Materials Engineering and Performance, 2021, 30 : 5278 - 5289
  • [25] Three-dimensional finite element analysis of thermal stress in single-pass multi-layer weld-based rapid prototyping
    Zhao, Huihui
    Zhang, Guangjun
    Yin, Ziqiang
    Wu, Lin
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2012, 212 (01) : 276 - 285
  • [26] The effect of WAAM process parameters on process conditions and production metrics in the fabrication of single-pass multi-layer wall artifacts
    Thien, Austen
    Saldana, Christopher
    Kurfess, Thomas
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2022, 119 (1-2): : 531 - 547
  • [27] Modeling of thermal behavior and mass transport in multi-layer laser additive manufacturing of Ni-based alloy on cast iron
    Gan, Zhengtao
    Liu, Hao
    Li, Shaoxia
    He, Xiuli
    Yu, Gang
    INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2017, 111 : 709 - 722
  • [28] A layer superposition strategy based on a theoretical model for wire and arc additive manufacturing of multi-layer single-bead components
    Zhang, Liang
    Sun, Meng
    Wang, Huixia
    Wang, Jun
    Bian, Wenzhuo
    Dai, Xuerui
    CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2024, 49 : 191 - 202
  • [29] The effect of WAAM process parameters on process conditions and production metrics in the fabrication of single-pass multi-layer wall artifacts
    Austen Thien
    Christopher Saldana
    Thomas Kurfess
    The International Journal of Advanced Manufacturing Technology, 2022, 119 : 531 - 547
  • [30] Deposition Time and Thermal Cycles of Fabricating Thin-wall Steel Parts by Double Electrode GMAW Based Additive Manufacturing
    Yang, Dongqing
    Zhang, Guangjun
    2016 INTERNATIONAL CONFERENCE ON BIOMATERIALS, NANOMATERIALS AND COMPOSITE MATERIALS (CBNCM 2016), 2017, 88