Penetration Enhancement Behavior of Reactive Material Double-Layered Liner Shaped Charge

被引:0
作者
Guo H.-G. [1 ]
Lu G.-C. [1 ]
He S. [1 ]
Wang H.-F. [1 ]
Xiao Y.-W. [2 ]
Zheng Y.-F. [1 ]
机构
[1] State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing
[2] Equipment Project Management Center, Army Equipment Department, Beijing
来源
Beijing Ligong Daxue Xuebao/Transaction of Beijing Institute of Technology | 2020年 / 40卷 / 12期
关键词
Double-layered liner; Penetration behavior; Reactive material; Shaped charge;
D O I
10.15918/j.tbit1001-0645.2019.247
中图分类号
学科分类号
摘要
To solve the problem of insufficient penetration depth of traditional polymer-based reactive liner shaped charge,a novel reactive material-copper liner shaped charge was designed. The jet formation and penetration enhancement behavior of the reactive material-copper jet against steel target were studied through combining simulations and experiments. Numerical simulations indicate that the inner copper liner mainly forms a high-velocity precursor jet to firstly penetrate the steel target,and the outer reactive liner becomes a major part of the slug,which can follow the copper jet into the penetration hole. Experimental results show that,compared with the traditional single reactive jet,this reactive material-copper jet produces a deeper penetration depth,and its penetration performance and reactive material mass entering the penetration hole are strongly influenced by the standoff. Further comparison analysis demonstrates that the deflagration reaction of reactive materials will lead to an early termination of the penetration process,and the likely mechanism is that reactive materials' chemical reaction would cause the serious instability of copper jet,eventually resulting in the residual jet not being able to continue penetration. © 2020, Editorial Department of Transaction of Beijing Institute of Technology. All right reserved.
引用
收藏
页码:1259 / 1266
页数:7
相关论文
共 12 条
[1]  
Baker E L, Daniels A S, Ng K W, Et al., Barnie:a unitary demolition warhead [C], Proceedings of the 19th International Symposium on Ballistics, pp. 569-574, (2001)
[2]  
Daniels A S, Baker E L, DeFisher S E, Et al., Bam bam:large scale unitary demolition warheads [C], Proceedings of the 23rd International Symposium on Ballistics, pp. 58-67, (2007)
[3]  
Jianguang Xiao, Xuepeng Zhang, Guo Zhangxia, Et al., Enhanced damage effects of multi-layered concrete target produced by reactive materials liner [J], Propellants Explosives Pyrotechnics, 43, pp. 955-961, (2018)
[4]  
Zhang Xuepeng, Xiao Jianguang, Yu Qingbo, Et al., Demolition effect of reactive material liner shaped charge against concrete target [J], Transactions of Beijing Institute of Technology, 36, 12, pp. 1211-1215, (2016)
[5]  
Huanguo Guo, Zheng Yuanfeng, Yu Qingbo, Et al., Penetration behavior of reactive liner shaped charge jet impacting steel plates [J], International Journal of Impact Engineering, 126, pp. 76-84, (2019)
[6]  
Zhang Xuepeng, Xiao Jianguang, Yu Qingbo, Et al., Penetration and blast combined damage effects of reactive material jet against steel target [J], Transactions of Beijing Institute of Technology, 37, 8, pp. 789-793, (2017)
[7]  
Men Jianbing, Jiang Jianwei, Shuai Junfeng, Et al., Experimental research on formation and terminal effect of explosively formed compound reactive fragments [J], Transactions of Beijing Institute of Technology, 30, 10, pp. 1143-1146, (2010)
[8]  
Zhang Xuepeng, Xiao Jianguang, Yu Qingbo, Et al., Armor penetration aftereffect overpressure produced by reactive material liner shaped charge [J], Acta Armamentarii, 37, 8, pp. 1388-1394, (2016)
[9]  
Zheng Yu, Wang Xiaoming, Li Wenbin, Numerical simulation on double-layered shaped charge liner penetration into semi-infinite target [J], Journal of Nanjing University of Science and Technology(Natural Science), 32, 3, pp. 313-317, (2008)
[10]  
Liu Han, Men Jianbing, Jiang Jianwei, Et al., Verification for numerical simulation rules of the shaped charge based on LS-DYNA 3D [J], Transactions of Beijing Institute of Technology, 37, pp. 174-182, (2017)