Direct Torque Control of Induction Motor with Stator Flux Estimation Based on an Improved Voltage Model

被引：0

作者：

Belbali A. ^{[1
]}

Makhloufi S. ^{[1
]}

机构：

[1] Department of hydrocarbons and renewable energies, Ahmed DRAIA University, Adrar

来源：

Electronics | 2022年 / 26卷 / 01期

关键词：

Direct torque control; Electromotive force; Estimator; Fractional order integrator; Fractional order low pass filter; Induction motor; Voltage model;

D O I：

10.53314/ELS2226026B

中图分类号：

学科分类号：

摘要：

Using sensors to measure the stator flux for induction motor presents many drawbacks such as far less reliability, noisy signals, vibration, and additional cost. Thus, it is essential to synthesize an estimator (also called a software sensor) allowing to replace the hardware sensor, for the flux estimation. In general, this estimation is done by integrating the back electromotive force (EMF) of the stator. However, the presence of the pure integrator presents problems due to the inevitable DC component and the initial condition error in the back EMF. To overcome these problems, a low pass filter has been used in the literature. Nevertheless, this solution does not solve the problem of undesirable high-frequency noise, especially at low speed. In this paper, we present a solution to improve the stator flux estimator by proposing a fractional order integrator to estimate the flux at low speed. This solution does not require any hardware device; it involves low calculation time and provides accurate practical results. The proposed solution has been implemented using the dSPACE 1104 platform © 2022. Electronics.All Rights Reserved.

引用

页码：26 / 33

页数：7

共 35 条

[1]

Wang K., Et al., Online updating of rotor time constant based on combined voltage and current mode flux observer for speed-sensorless AC drives, IEEE Transactions on Industrial Electronics, 61, pp. 4583-4593, (2014)

[2]

Lascu C., Boldea I., Blaabjerg F., A modified direct torque control for induction motor sensorless drive, IEEE Transactions on industry applications, 36, pp. 122-130, (2000)

[3]

Krim S., Gdaim S., Mtibaa A., Mimouni M. F., Hardware Implementation of a Predictive DTC-SVM with a Sliding Mode Observer of an Induction Motor on the FPGA, WSEAS Transactions on Systems and Control, 10, pp. 2224-2856, (2015)

[4]

Lascu C., Andreescu G.-D., Sliding-mode observer and improved integrator with DC-offset compensation for flux estimation in sensorless-controlled induction motors, IEEE Transactions on Industrial Electronics, 53, pp. 785-794, (2006)

[5]

Yin Z. G., Zhao C., Zhong Y. R., Liu J., Research on robust performance of speed-sensorless vector control for the induction motor using an interfacing multiple-model extended Kalman filter, IEEE Transactions on Power Electronics, 29, pp. 3011-3019, (2013)

[6]

Gadoue S. M., Giaouris D., Finch J. W., Sensorless control of induction motor drives at very low and zero speeds using neural network flux observers, IEEE Transactions on Industrial Electronics, 56, pp. 3029-3039, (2009)

[7]

Gadoue S. M., Giaouris D., Finch J. W., MRAS sensorless vector control of an induction motor using new sliding-mode and fuzzy-logic adaptation mechanisms, IEEE Transactions on Energy conversion, 25, pp. 394-402, (2009)

[8]

Xu W., Qu S., Zhao J., Zhang H., Du X., An Improved Full-Order Sliding-Mode Observer for Rotor Position and Speed Estimation of SPMSM, IEEE Access, 9, pp. 15099-15109, (2021)

[9]

Xu X., Novotny D.W., Implementation of direct stator flux orientation control on a versatile DSP based system, IEEE Transactions on Industry Applications, 27, pp. 694-700, (1991)

[10]

Benlaloui I., Drid S., Chrifi-Alaoui L., Ouriagli M., Implementation of a new MRAS speed sensorless vector control of induction machine, IEEE Transactions on Energy conversion, 30, pp. 588-595, (2014)

← 1 2 3 4 →