Relation between flange fracture and blankholder force in the process of cylindrical deep drawing of AZ31B rolled magnesium alloy sheets

被引：0

作者：

Okawa M. ^{[1
]}

Mori S. ^{[1
]}

Murakami T. ^{[2
]}

Takasaki A. ^{[3
]}

机构：

[1] Plastic Forming Engineering Unit, Polytechnic University of Japan, 2-32-1 Ogawanishimachi, Kodaira-shi, Tokyo

[2] Instructional Methods of Human Resources Development Unit, Polytechnic University of Japan, Kodaira-shi, Tokyo

[3] Department o Engineering Science and Mechanics, Shibaura Institute of Technology, Koto-ku, Tokyo

来源：

Keikinzoku/Journal of Japan Institute of Light Metals | 2019年 / 69卷 / 02期

关键词：

Deep drawing; Flange edge fracture; Magnesium alloy sheet; Uniaxial in-plane compression;

D O I：

10.2464/jilm.69.113

中图分类号：

学科分类号：

摘要：

The fracture occurring at the flange edge in the process of cylindrical deep drawing of AZ31B magnesium alloy sheets was investigated. The fractures were simulated under a uniaxial in-plane compression test to classify the fracture types while the blankholder force of the sheet was varied. Two types of fractures, out-of-plane shear fracture (OPSF), and in-plane shear fracture (IPSF), were observed. The fracture types changed from OPSF to IPSF as the blankholder force increased to a drawing ratio of approximately 1.5-1.6. This implies that the fracture type could be controlled by changing the blankholder force. The transition from OPSF to IPSF increased the fracture strain, because the out of plane buckling of the alloy sheets was suppressed by the blankholder force. The results confirmed that, in cylindrical deep drawing, the limiting drawing ratio could be increased by restraining the flange edge of the alloy sheets with the sufficient blankholder force. © 2019 The Japan Institute of Light Metals.

引用

页码：113 / 119

页数：6

共 10 条

[1]

Wang Y., Huang J.C., Mater. Chem. Phys., 81, pp. 11-26, (2003)

[2]

Chino Y., Iwasaki H., Mabuchi M., Mater. Sci. Eng. A, 466, pp. 90-95, (2007)

[3]

Huang X., Suzuki K., Chino Y., Mabuchi M., J. Alloys Compd., 509, pp. 7579-7584, (2011)

[4]

Huang X., Suzuki K., Chino Y., Mabuchi M., Mater. Sci. Eng. A, 565, pp. 359-372, (2013)

[5]

Hai D.V., Itoh S., Sakai T., Kamado S., Kojima Y., Mater. Trans., 49, pp. 1101-1106, (2008)

[6]

Kohzu M., Hironaka T., Nakatsuka S., Saito N., Yoshida F., Naka T., Okahara H., Higashi K., Mater. Trans., 48, pp. 764-768, (2007)

[7]

Kemmis O.H., Sheet Metal Ind., 34, (1957)

[8]

Kuwabara T., Kumano Y., Ziegelheim J., Kurosaki I., Int. J. Plast., 25, pp. 1759-1776, (2009)

[9]

Kalpakjian S., Schmid S.R., Manufacturing Processes for Engineering Materials, pp. 395-397, (2008)

[10]

Hama T., Kariyazaki Y., Hosokawa N., Fujimoto H., Takuda H., Mater. Sci. Eng. A, 551, pp. 209-217, (2012)

← 1 →