An application of fuzzy logic with grey relational technique in grinding process using nano Al2O3 grinding wheel on Ti-6Al-4V alloy

被引：0

作者：

Stephen D.S. ^{[1
]}

Sethuramalingam P. ^{[1
]}

机构：

[1] Mechanical Engineering Department, SRM Institute of Science and Technology, Tamilnadu

来源：

International Journal of Machining and Machinability of Materials | 2021年 / 23卷 / 01期

关键词：

Abrasive grinding; Fuzzy logic analysis; GRA; Grey relational analysis; Material removal rate; MRR; Nano Al2O3 grinding wheel; Surface roughness;

D O I：

10.1504/IJMMM.2021.112715

中图分类号：

学科分类号：

摘要：

This investigation is focused on studying grinding of titanium alloys (Ti-6Al-4V) by using nano Al2O3 grinding wheel as an alternative approach to existing methods of grinding. To evaluate optimum conditions of grinding process output, a full factorial technique has been used. L27 orthogonal array was chosen to arrive at an optimised permutation of grinding depth of cut, speed and feed. Consequently, the optimal combination of parameters was tested and results were compared with those of a conventional grinding wheel. The results show superior surface finish on Ti alloy when ground with nano Al2O3 grinding wheel. Confirmatory tests assured that a great improvement in grey relational grade with fuzzy logic, from 0.551 to 0.749 was observed, which substantiates the progress in the performance at best possible levels of nano grinding parameters. Improvement of 21.47% in surface finish of the ground material using combinations of fuzzy grey relational analysis have been achieved. Copyright © 2021 Inderscience Enterprises Ltd.

引用

页码：21 / 46

页数：25

共 20 条

[11]

Osada T., Nakao W., Takahashi K., Ando K., Saito S., Strength recovery behavior of machined Al2O3/SiC nano-composite ceramics by crack-healing, Journal of the European Ceramic Society, 27, 10, pp. 3261-3267, (2007)

[12]

Rudrapati R., Bandyopadhyay A., Pal P.K., Multi-objective optimization in traverse cut cylindrical grinding, Adv. Mater. Manuf. Charact, 3, pp. 335-339, (2013)

[13]

Setti D., Ghosh S., Rao P.V., Application of nano cutting fluid under minimum quantity lubrication (MQL) technique to improve grinding of Ti-6Al-4V alloy, Proceedings of World Academy of Science, Engineering and Technology, 70, pp. 512-516, (2012)

[14]

Shabani M.O., Mazahery A., Application of GA to optimize the process conditions of Al Matrix nano-composites, Composites Part B: Engineering, 45, 1, pp. 185-191, (2013)

[15]

Suresh S.M., Mishra D., Srinivasan A., Arunachalam R.M., Sasikumar R., Production and characterization of micro and nano Al2O3 particle-reinforced LM25 aluminium alloy composites, Journal of Engineering and Applied Sciences, 6, 6, pp. 94-97, (2011)

[16]

Vasu V., Kumar K.M., Analysis of nanofluids as cutting fluid in grinding EN-31 steel, Nano-Micro Letters, 3, 4, pp. 209-214, (2011)

[17]

Virdi R.L., Chatha S.S., Singh H., Experiment evaluation of grinding properties under Al2O3 nanofluids in minimum quantity lubrication, Materials Research Express, 6, 9, (2019)

[18]

Yin Z., Huang C., Zou B., Liu H., Zhu H., Wang J., Study of the mechanical properties, strengthening and toughening mechanisms of Al2O3/TiC micro-nano-composite ceramic tool material, Materials Science and Engineering: A, 577, pp. 9-15, (2013)

[19]

Zhang .Y., You J., A study of uncut chips produced by CNT grinding wheel, Advanced Materials Research, 126-128, pp. 879-884, (2010)

[20]

Zheng L.Y., Lau K.T., Zhao L.X., Zhang Y.Q., Hui D., Mechanical and thermal properties of nano-Al2O3/nylon 6 composites, Chemical Engineering Communications, 197, 3, pp. 343-351, (2009)

← 1 2 →